JVC 0802MWMMDWJEM, LVT0900-008A Listening to External Equipment, Adjusting the Audio Input Level

Page 35

Listening to External Equipment

You can listen to external equipment connected to the AUX/DVD jacks on the rear of the unit.

First make sure that the external equipment is properly connected as follows:

DO NOT connect other equipment while the power is on.

 

Right

External equipment

 

 

Left

 

R

 

L

 

To AUX/DVD jacks

SPEAKERS

R

L

CAUTION: R

L

SPEAKER IMPEDANCE 4~16

1 Press FM/AM/AUX (or AUX/DVD on the main unit) repeatedly so that “AUX” appears in the main display.

On the remote control:

Each time you press the button, the source changes as follows:

FM AM

AUX

2 Adjust the volume level of the unit to “VOLUME 0.”

3 Start playing the external equipment.

For operation of the external equipment, see the manuals supplied with it.

4 Adjust the volume level of the unit to your desired listening level.

5 Apply sound effects, if you wish.

• For how to apply sound effects, see page 14.

Adjusting the Audio Input Level

If the sound from the component connected to the AUX/DVD jacks is too loud or is not loud enough when changing from another source to “AUX” (without changing the volume level), you can change the audio input level through the AUX/DVD jacks.

1 Press FM/AM/AUX (or AUX/DVD on the main unit) repeatedly so that “AUX” appears in the main display.

On the remote control:

Each time you press the button, the source changes as follows:

FM AM

AUX

2 Press and hold SET on the remote control for more than 2 seconds.

Each time you press and hold the button, the audio input level alternates between “LEVEL 1” and “LEVEL 2.”

LEVEL 1: Select this when the sound is too loud (initial setting).

LEVEL 2: Select this when the sound is not loud enough.

To change the information shown in the main display

On the remote control ONLY:

Each time you press DISP/CHARA, the information in the main display alternates between the source indication and the clock indication.

If an MD is inserted, the MD remaining recording time (“REC REMAIN”) is shown before the clock indication.

– 32 –

Image 35
Contents UX-Z7MD-Consists of CA-UXZ7MD and SP-UXZ7MD Micro Component MD SystemPage Class Laser Product Introduction PrecautionsContents Main unit Location of the ButtonsMain Unit Display window Display window on the electronic swing panelPressing one of these buttons also turns on the unit Remote ControlFM antenna Connecting AntennasGetting Started UnpackingTo connect an outdoor AM antenna Connecting SpeakersYou can connect the speakers using the speaker cords AM antennaSpeaker grilles are removable as illustrated below Connecting External EquipmentTo remove the speaker grilles To connect external equipmentR6PSUM-3/AA15F Putting the Batteries into the Remote ControlBasic and Common Operations Remote controlTurning On/Off the Key-touch Tone Turning On the PowerSetting the Auto Power Off To check the clock time with tones Setting the ClockTo turn off the clock indication power save mode For private listening To increase the volume, turn Volume + / control ClockwiseIf Cannot Listen appears in the main display Selecting the Sound Modes To check the sound mode currently selected, pressSound indicator goes off from the display Reinforcing the Bass SoundTo change the display brightness Setting the Display IlluminationTo select the illumination color To create your favorite colorsListening to FM and AM Broadcasts Remote control Main unitTo stop during searching, press ¢or 4or UP or Tuning in to a StationTo change the FM reception mode On the remote control only Press FM ModePress SET Presetting StationsTuning in to a Preset Station Press the number buttons to select a preset numberPlaying Back CDs CD-R/CD-RW Playing Back the Entire CD-Normal Play Precautions on CD PlaybackTo stop playback for a moment To go to another track directly using the number buttonsBasic CD Operations Program PlayTo modify the program To check the program contentsPlaying at Random-Random Play Repeating Tracks-Repeat PlayPlaying Back MDs To locate a particular point in a track during play Basic MD OperationsOn the main unit only To prohibit disc ejection About MD indicatorWhile playing or pausing On the remote control only Load an MD Press MD 3/8, thenTo skip the playing track, press ¢ To erase the entire program, press MD 0 to eject the MDTracks of the loaded MD will play at random Tracks are played at randomTo go to another group, press Group Skip Playing Tracks in a Group-Group PlayPress Group Skip or Group Skip to select a group To go to another track in the same group, press ¢ orSearching for Tracks to Play MD Title Search Playing Back Tapes To change the information shown in the main display To play both sides-Reverse modePlaying Back a Tape Listening to External Equipment Listening to External Equipment Adjusting the Audio Input LevelFor how to apply sound effects, see Recording To put a track mark manually while recording an Before You Start Recording on an MDAbout the track marks To avoid erasing important recordingsTo check the remaining recording time Precautions for performing long-hour stereo recordingStereo Long-Hour Recording Mdlp About High-Speed RecordingTo set Group recording mode Setting MD Recording ModesTo set the recording length mode To set LP-prefix addition modeTo record a single track during play or pause Recording Other Sources onto an MDTo keep the best recording and playback sound quality To clean the heads, capstans, and pinch rollersBefore You Start Recording on a Tape To protect your recordingsTo record an MD Recording onto a TapeTo record a single track of a CD/MD during play Prepare the source to record To record a discPress MD&TAPE REC Press REV.MODE to select the reverse modeWhen recording on an MD and a tape at the same time For the tapeEditing MDs Classifying the tracks on an MD Using MD Group functionsHow to make up Groups Guidance-MD Group FunctionsIntroducing Group Editing Functions Press ¢or 4to select the last track of the new group Forming a Group-FORM GRPress SET During playback Press ¢or 4to select the first track of a new groupOr Group Skip When Cannot ENTRY! appears in stepAdding a Track to a Group-ENTRY GR Press ¢or 4to select the trackFunction on Dividing a Group-DIVIDE GRTo join the divided groups again, see the Join GR To divide the group again, see the Divide GR function When Cannot Join appears in stepJoining Two Groups-JOIN GR Moving a Group-MOVE GR Dissolving All Groups-UNGR ALL To cancel the setting, press CancelUngrouping Tracks-UNGROUP Erasing Tracks in a Group-ERASE GR Introducing Track Editing Functions To join the divided tracks again, see the Join function Press or to precisely adjust the dividing pointDividing a Track-DIVIDE Press ¢or 4to select the track you want to divideIf Cannot Join appears in step When the track belongs to a groupJoining Two Tracks-JOIN To divide the joined tracks, see the Divide function onPress ¢or 4to select the track you want to move Moving a Track-MOVEPress SET Press ¢or 4to select the track you want to erase Erasing Tracks-ERASEErasing All Tracks-ALL Erase For the disc and track title Press or to change the title entry modeAssigning Titles to an MD For the group titleFor the disc title Press Cancel to exit from the title entry modeRepeat steps 5 1 and 5 2 to enter other characters Press Enter to finish the current title entryMake sure that the character you want to change is flashing Changing the TitleYou can make a correction or change the title Using the Timers How Recording Timer actually works Using Recording TimerTo turn on the Recording Timer again Using Daily TimerHow Daily Timer actually works To turn off the Recording Timer after its setting is doneIf the unit is kept turned on when the timer-on time comes To turn off the Daily Timer after its setting is doneTo turn on the Daily Timer again Volume setting appears in the main displayHow Sleep Timer actually works Using Sleep TimerTimer Priority Maintenance Atrac Adaptive TRansform Acoustic Coding/ATRAC3 Utoc User Table Of ContentsAdditional Information MD Disc TypesMD limitations Symptoms CauseScms Serial Copy Management System Hcms High-speed Copy Management SystemCannot REC x1 or x2 only CD/MD MessagesCannot REC x1 REC only Message Symptom TroubleshootingAmplifier Section-CA-UXZ7MD SpecificationsVictor Company of JAPAN, Limited