JVC 0802MWMMDWJEM manual Presetting Stations, Tuning in to a Preset Station, Press SET again

Page 21

Presetting Stations

You can preset 30 FM and 15 AM stations manually.

In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

On the remote control ONLY:

1 Tune in to the station (either FM or AM) you want to preset.

• See “Tuning in to a Station” on the previous page.

2 Press SET.

The preset number starts flashing as follows:

Ex.: When you select an FM station in step 1.

• The unit always starts from the preset number 1.

3 Press the number buttons to select a preset number.

Ex.: For preset number 5, press 5.

For preset number 15, press +10, then 5. For preset number 20, press +10, then 10.

For preset number 30, press +10, +10, then 10.

•You can also select the preset number by pressing ¢or 4.

4 Press SET again.

“STORED” appears in the main display for a while.

The tuned station in step 1 is stored in the preset number selected in step 3.

•Storing a new station on a used number erases the previously stored one.

When you unplug the AC power cord or if a power failure occurs

The FM and AM preset stations will be erased in a day. If this happens, preset the stations again.

Tuning in to a Preset Station

On the remote control ONLY:

1 Press FM/AM/AUX to select either “FM” or “AM.”

When you press the button for the first time, the unit automatically turns on with the last selected source.

•Each time you press the button, the source changes as follows:

FM AM

AUX

2 Press the number buttons to select a preset number.

Ex.: For preset number 5, press 5.

For preset number 15, press +10, then 5. For preset number 20, press +10, then 10.

For preset number 30, press +10, +10, then 10.

– 18 –

Image 21

Contents UX-Z7MD-Consists of CA-UXZ7MD and SP-UXZ7MD Micro Component MD SystemPage Class Laser Product Introduction PrecautionsContents Location of the Buttons Main UnitMain unit Display window Display window on the electronic swing panelPressing one of these buttons also turns on the unit Remote ControlGetting Started Connecting AntennasUnpacking FM antennaYou can connect the speakers using the speaker cords Connecting SpeakersAM antenna To connect an outdoor AM antennaTo remove the speaker grilles Connecting External EquipmentTo connect external equipment Speaker grilles are removable as illustrated belowR6PSUM-3/AA15F Putting the Batteries into the Remote ControlBasic and Common Operations Remote controlTurning On the Power Setting the Auto Power OffTurning On/Off the Key-touch Tone Setting the Clock To turn off the clock indication power save modeTo check the clock time with tones To increase the volume, turn Volume + / control Clockwise If Cannot Listen appears in the main displayFor private listening Sound indicator goes off from the display To check the sound mode currently selected, pressReinforcing the Bass Sound Selecting the Sound ModesTo select the illumination color Setting the Display IlluminationTo create your favorite colors To change the display brightnessListening to FM and AM Broadcasts Remote control Main unitTo change the FM reception mode Tuning in to a StationOn the remote control only Press FM Mode To stop during searching, press ¢or 4or UP orTuning in to a Preset Station Presetting StationsPress the number buttons to select a preset number Press SETPlaying Back CDs CD-R/CD-RW Playing Back the Entire CD-Normal Play Precautions on CD PlaybackBasic CD Operations To go to another track directly using the number buttonsProgram Play To stop playback for a momentPlaying at Random-Random Play To check the program contentsRepeating Tracks-Repeat Play To modify the programPlaying Back MDs To locate a particular point in a track during play Basic MD OperationsWhile playing or pausing About MD indicatorOn the remote control only Load an MD Press MD 3/8, then On the main unit only To prohibit disc ejectionTracks of the loaded MD will play at random To erase the entire program, press MD 0 to eject the MDTracks are played at random To skip the playing track, press ¢Press Group Skip or Group Skip to select a group Playing Tracks in a Group-Group PlayTo go to another track in the same group, press ¢ or To go to another group, press Group SkipSearching for Tracks to Play MD Title Search Playing Back Tapes To play both sides-Reverse mode Playing Back a TapeTo change the information shown in the main display Listening to External Equipment Adjusting the Audio Input Level For how to apply sound effects, seeListening to External Equipment Recording About the track marks Before You Start Recording on an MDTo avoid erasing important recordings To put a track mark manually while recording anStereo Long-Hour Recording Mdlp Precautions for performing long-hour stereo recordingAbout High-Speed Recording To check the remaining recording timeTo set the recording length mode Setting MD Recording ModesTo set LP-prefix addition mode To set Group recording modeTo record a single track during play or pause Recording Other Sources onto an MDBefore You Start Recording on a Tape To clean the heads, capstans, and pinch rollersTo protect your recordings To keep the best recording and playback sound qualityTo record a single track of a CD/MD during play Recording onto a TapePrepare the source to record To record a disc To record an MDWhen recording on an MD and a tape at the same time Press REV.MODE to select the reverse modeFor the tape Press MD&TAPE RECEditing MDs How to make up Groups Using MD Group functionsGuidance-MD Group Functions Classifying the tracks on an MDIntroducing Group Editing Functions Press SET During playback Forming a Group-FORM GRPress ¢or 4to select the first track of a new group Press ¢or 4to select the last track of the new groupAdding a Track to a Group-ENTRY GR When Cannot ENTRY! appears in stepPress ¢or 4to select the track Or Group SkipDividing a Group-DIVIDE GR To join the divided groups again, see the Join GRFunction on When Cannot Join appears in step Joining Two Groups-JOIN GRTo divide the group again, see the Divide GR function Moving a Group-MOVE GR To cancel the setting, press Cancel Ungrouping Tracks-UNGROUPDissolving All Groups-UNGR ALL Erasing Tracks in a Group-ERASE GR Introducing Track Editing Functions Dividing a Track-DIVIDE Press or to precisely adjust the dividing pointPress ¢or 4to select the track you want to divide To join the divided tracks again, see the Join functionJoining Two Tracks-JOIN When the track belongs to a groupTo divide the joined tracks, see the Divide function on If Cannot Join appears in stepPress ¢or 4to select the track you want to move Moving a Track-MOVEErasing Tracks-ERASE Erasing All Tracks-ALL ErasePress SET Press ¢or 4to select the track you want to erase Assigning Titles to an MD Press or to change the title entry modeFor the group title For the disc and track titleRepeat steps 5 1 and 5 2 to enter other characters Press Cancel to exit from the title entry modePress Enter to finish the current title entry For the disc titleChanging the Title You can make a correction or change the titleMake sure that the character you want to change is flashing Using the Timers How Recording Timer actually works Using Recording TimerHow Daily Timer actually works Using Daily TimerTo turn off the Recording Timer after its setting is done To turn on the Recording Timer againTo turn on the Daily Timer again To turn off the Daily Timer after its setting is doneVolume setting appears in the main display If the unit is kept turned on when the timer-on time comesUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Maintenance Additional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Scms Serial Copy Management System Symptoms CauseHcms High-speed Copy Management System MD limitationsCD/MD Messages Cannot REC x1 REC onlyCannot REC x1 or x2 only Message Symptom TroubleshootingAmplifier Section-CA-UXZ7MD SpecificationsVictor Company of JAPAN, Limited