JVC LVT0900-008A Connecting Speakers, To connect an outdoor AM antenna, To connect speakers

Page 10

AM antenna

1

2

Vinyl-covered wire

(not supplied)

3

AM loop antenna

(supplied)

1If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.

2Connect the AM loop antenna to the AM LOOP terminals as illustrated.

3Turn the AM loop antenna until you have the best reception.

To connect an outdoor AM antenna

When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. The AM loop antenna must remain connected.

For better reception of both FM and AM

•Make sure the antenna conductors do not touch any other terminals and connecting cords.

•Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.

Connecting Speakers

To connect speakers

You can connect the speakers using the speaker cords.

1
2	Speaker terminals		3,4
		Black
Red	SPEAKERS		Red
Red	R	L	Red
	CAUTION: R	L
Black	SPEAKER IMPEDANCE 4~16Ω		Black
Black			Black
	Speaker cord
Rear of the right			Rear of the left
speaker			speaker

1If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.

2Hold the clamp of the speaker terminal.

3Insert the end of the speaker cord to the terminal. Match the polarity of the speaker terminals: Red (+) to red (+) and black (–) to black (–).

4Release the finger from the clamp.

IMPORTANT

•Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.

•DO NOT connect more than one speaker to one speaker terminal.

– 7 –

Image 10

Contents Micro Component MD System UX-Z7MD-Consists of CA-UXZ7MD and SP-UXZ7MDPage Class Laser Product Precautions IntroductionContents Main Unit Location of the ButtonsMain unit Display window on the electronic swing panel Display windowRemote Control Pressing one of these buttons also turns on the unitUnpacking Connecting AntennasGetting Started FM antennaAM antenna Connecting SpeakersYou can connect the speakers using the speaker cords To connect an outdoor AM antennaTo connect external equipment Connecting External EquipmentTo remove the speaker grilles Speaker grilles are removable as illustrated belowPutting the Batteries into the Remote Control R6PSUM-3/AA15FRemote control Basic and Common OperationsSetting the Auto Power Off Turning On the PowerTurning On/Off the Key-touch Tone To turn off the clock indication power save mode Setting the ClockTo check the clock time with tones If Cannot Listen appears in the main display To increase the volume, turn Volume + / control ClockwiseFor private listening Reinforcing the Bass Sound To check the sound mode currently selected, pressSound indicator goes off from the display Selecting the Sound ModesTo create your favorite colors Setting the Display IlluminationTo select the illumination color To change the display brightnessRemote control Main unit Listening to FM and AM BroadcastsOn the remote control only Press FM Mode Tuning in to a StationTo change the FM reception mode To stop during searching, press ¢or 4or UP orPress the number buttons to select a preset number Presetting StationsTuning in to a Preset Station Press SETPlaying Back CDs CD-R/CD-RW Precautions on CD Playback Playing Back the Entire CD-Normal PlayProgram Play To go to another track directly using the number buttonsBasic CD Operations To stop playback for a momentRepeating Tracks-Repeat Play To check the program contentsPlaying at Random-Random Play To modify the programPlaying Back MDs Basic MD Operations To locate a particular point in a track during playOn the remote control only Load an MD Press MD 3/8, then About MD indicatorWhile playing or pausing On the main unit only To prohibit disc ejectionTracks are played at random To erase the entire program, press MD 0 to eject the MDTracks of the loaded MD will play at random To skip the playing track, press ¢To go to another track in the same group, press ¢ or Playing Tracks in a Group-Group PlayPress Group Skip or Group Skip to select a group To go to another group, press Group SkipSearching for Tracks to Play MD Title Search Playing Back Tapes Playing Back a Tape To play both sides-Reverse modeTo change the information shown in the main display Listening to External Equipment For how to apply sound effects, see Adjusting the Audio Input LevelListening to External Equipment Recording To avoid erasing important recordings Before You Start Recording on an MDAbout the track marks To put a track mark manually while recording anAbout High-Speed Recording Precautions for performing long-hour stereo recordingStereo Long-Hour Recording Mdlp To check the remaining recording timeTo set LP-prefix addition mode Setting MD Recording ModesTo set the recording length mode To set Group recording modeRecording Other Sources onto an MD To record a single track during play or pauseTo protect your recordings To clean the heads, capstans, and pinch rollersBefore You Start Recording on a Tape To keep the best recording and playback sound qualityPrepare the source to record To record a disc Recording onto a TapeTo record a single track of a CD/MD during play To record an MDFor the tape Press REV.MODE to select the reverse modeWhen recording on an MD and a tape at the same time Press MD&TAPE RECEditing MDs Guidance-MD Group Functions Using MD Group functionsHow to make up Groups Classifying the tracks on an MDIntroducing Group Editing Functions Press ¢or 4to select the first track of a new group Forming a Group-FORM GRPress SET During playback Press ¢or 4to select the last track of the new groupPress ¢or 4to select the track When Cannot ENTRY! appears in stepAdding a Track to a Group-ENTRY GR Or Group SkipTo join the divided groups again, see the Join GR Dividing a Group-DIVIDE GRFunction on Joining Two Groups-JOIN GR When Cannot Join appears in stepTo divide the group again, see the Divide GR function Moving a Group-MOVE GR Ungrouping Tracks-UNGROUP To cancel the setting, press CancelDissolving All Groups-UNGR ALL Erasing Tracks in a Group-ERASE GR Introducing Track Editing Functions Press ¢or 4to select the track you want to divide Press or to precisely adjust the dividing pointDividing a Track-DIVIDE To join the divided tracks again, see the Join functionTo divide the joined tracks, see the Divide function on When the track belongs to a groupJoining Two Tracks-JOIN If Cannot Join appears in stepMoving a Track-MOVE Press ¢or 4to select the track you want to moveErasing All Tracks-ALL Erase Erasing Tracks-ERASEPress SET Press ¢or 4to select the track you want to erase For the group title Press or to change the title entry modeAssigning Titles to an MD For the disc and track titlePress Enter to finish the current title entry Press Cancel to exit from the title entry modeRepeat steps 5 1 and 5 2 to enter other characters For the disc titleYou can make a correction or change the title Changing the TitleMake sure that the character you want to change is flashing Using the Timers Using Recording Timer How Recording Timer actually worksTo turn off the Recording Timer after its setting is done Using Daily TimerHow Daily Timer actually works To turn on the Recording Timer againVolume setting appears in the main display To turn off the Daily Timer after its setting is doneTo turn on the Daily Timer again If the unit is kept turned on when the timer-on time comesTimer Priority Using Sleep TimerHow Sleep Timer actually works Maintenance MD Disc Types Utoc User Table Of ContentsAdditional Information Atrac Adaptive TRansform Acoustic Coding/ATRAC3Hcms High-speed Copy Management System Symptoms CauseScms Serial Copy Management System MD limitationsCannot REC x1 REC only CD/MD MessagesCannot REC x1 or x2 only Message Troubleshooting SymptomSpecifications Amplifier Section-CA-UXZ7MDVictor Company of JAPAN, Limited