JVC LVT0900-008A, 0802MWMMDWJEM manual Tuning in to a Station, To change the FM reception mode

Page 20

Tuning in to a Station

1 Press FM/AM/AUX (or FM/AM on the main unit) to select either “FM” or “AM.”

When you press the button for the first time, the unit automatically turns on with the last selected source.

On the remote control:

•Each time you press the button, the source changes as follows:

FM AM

AUX

On the main unit:

•Each time you press the button, the band alternates between FM and AM.

2 Press and hold ¢or 4(UP or DOWN on the main unit) until the station frequencies start changing continuously in the main display.

•	¢	(UP):	Increases the frequencies.
•	4	(DOWN):	Decreases the frequencies.

The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in.

•If an FM program is broadcast in stereo, the STEREO indicator lights up on the display.

To stop during searching, press ¢or 4(or UP or

DOWN on the main unit).

To change the FM reception mode

When an FM stereo broadcast is noisy or hard to receive, you can change the FM reception mode to improve the reception.

On the remote control ONLY:

Press FM MODE.

•Each time you press the button, FM reception mode alternates between STEREO and MONO.

STEREO: Normally select this.

You can hear stereo sound when a program is broadcast in stereo. The STEREO indicator lights while receiving the FM stereo broadcast (only when the reception is good).

MONO: Select this when an FM stereo broadcast is noisy or hard to receive. Reception improves though stereo effect is lost. The MONO indicator lights up on the display.

To change the information shown in the main display

On the remote control ONLY:

Each time you press DISP/CHARA, the information in the main display alternates between the source indication and the clock indication.

•If an MD is inserted, the MD remaining recording time (“REC REMAIN”) is shown before the clock indication.

When you repeatedly press ¢or 4(or UP or

DOWN on the main unit)

The frequency changes step by step.

– 17 –

Image 20

Contents Micro Component MD System UX-Z7MD-Consists of CA-UXZ7MD and SP-UXZ7MDPage Class Laser Product Precautions IntroductionContents Main unit Location of the ButtonsMain Unit Display window on the electronic swing panel Display windowRemote Control Pressing one of these buttons also turns on the unitConnecting Antennas Getting StartedUnpacking FM antennaConnecting Speakers You can connect the speakers using the speaker cordsAM antenna To connect an outdoor AM antennaConnecting External Equipment To remove the speaker grillesTo connect external equipment Speaker grilles are removable as illustrated belowPutting the Batteries into the Remote Control R6PSUM-3/AA15FRemote control Basic and Common OperationsTurning On/Off the Key-touch Tone Turning On the PowerSetting the Auto Power Off To check the clock time with tones Setting the ClockTo turn off the clock indication power save mode For private listening To increase the volume, turn Volume + / control ClockwiseIf Cannot Listen appears in the main display To check the sound mode currently selected, press Sound indicator goes off from the displayReinforcing the Bass Sound Selecting the Sound ModesSetting the Display Illumination To select the illumination colorTo create your favorite colors To change the display brightnessRemote control Main unit Listening to FM and AM BroadcastsTuning in to a Station To change the FM reception modeOn the remote control only Press FM Mode To stop during searching, press ¢or 4or UP orPresetting Stations Tuning in to a Preset StationPress the number buttons to select a preset number Press SETPlaying Back CDs CD-R/CD-RW Precautions on CD Playback Playing Back the Entire CD-Normal PlayTo go to another track directly using the number buttons Basic CD OperationsProgram Play To stop playback for a momentTo check the program contents Playing at Random-Random PlayRepeating Tracks-Repeat Play To modify the programPlaying Back MDs Basic MD Operations To locate a particular point in a track during playAbout MD indicator While playing or pausingOn the remote control only Load an MD Press MD 3/8, then On the main unit only To prohibit disc ejectionTo erase the entire program, press MD 0 to eject the MD Tracks of the loaded MD will play at randomTracks are played at random To skip the playing track, press ¢Playing Tracks in a Group-Group Play Press Group Skip or Group Skip to select a groupTo go to another track in the same group, press ¢ or To go to another group, press Group SkipSearching for Tracks to Play MD Title Search Playing Back Tapes To change the information shown in the main display To play both sides-Reverse modePlaying Back a Tape Listening to External Equipment Listening to External Equipment Adjusting the Audio Input LevelFor how to apply sound effects, see Recording Before You Start Recording on an MD About the track marksTo avoid erasing important recordings To put a track mark manually while recording anPrecautions for performing long-hour stereo recording Stereo Long-Hour Recording MdlpAbout High-Speed Recording To check the remaining recording timeSetting MD Recording Modes To set the recording length modeTo set LP-prefix addition mode To set Group recording modeRecording Other Sources onto an MD To record a single track during play or pauseTo clean the heads, capstans, and pinch rollers Before You Start Recording on a TapeTo protect your recordings To keep the best recording and playback sound qualityRecording onto a Tape To record a single track of a CD/MD during playPrepare the source to record To record a disc To record an MDPress REV.MODE to select the reverse mode When recording on an MD and a tape at the same timeFor the tape Press MD&TAPE RECEditing MDs Using MD Group functions How to make up GroupsGuidance-MD Group Functions Classifying the tracks on an MDIntroducing Group Editing Functions Forming a Group-FORM GR Press SET During playbackPress ¢or 4to select the first track of a new group Press ¢or 4to select the last track of the new groupWhen Cannot ENTRY! appears in step Adding a Track to a Group-ENTRY GRPress ¢or 4to select the track Or Group SkipFunction on Dividing a Group-DIVIDE GRTo join the divided groups again, see the Join GR To divide the group again, see the Divide GR function When Cannot Join appears in stepJoining Two Groups-JOIN GR Moving a Group-MOVE GR Dissolving All Groups-UNGR ALL To cancel the setting, press CancelUngrouping Tracks-UNGROUP Erasing Tracks in a Group-ERASE GR Introducing Track Editing Functions Press or to precisely adjust the dividing point Dividing a Track-DIVIDEPress ¢or 4to select the track you want to divide To join the divided tracks again, see the Join functionWhen the track belongs to a group Joining Two Tracks-JOINTo divide the joined tracks, see the Divide function on If Cannot Join appears in stepMoving a Track-MOVE Press ¢or 4to select the track you want to movePress SET Press ¢or 4to select the track you want to erase Erasing Tracks-ERASEErasing All Tracks-ALL Erase Press or to change the title entry mode Assigning Titles to an MDFor the group title For the disc and track titlePress Cancel to exit from the title entry mode Repeat steps 5 1 and 5 2 to enter other charactersPress Enter to finish the current title entry For the disc titleMake sure that the character you want to change is flashing Changing the TitleYou can make a correction or change the title Using the Timers Using Recording Timer How Recording Timer actually worksUsing Daily Timer How Daily Timer actually worksTo turn off the Recording Timer after its setting is done To turn on the Recording Timer againTo turn off the Daily Timer after its setting is done To turn on the Daily Timer againVolume setting appears in the main display If the unit is kept turned on when the timer-on time comesHow Sleep Timer actually works Using Sleep TimerTimer Priority Maintenance Utoc User Table Of Contents Additional InformationMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Symptoms Cause Scms Serial Copy Management SystemHcms High-speed Copy Management System MD limitationsCannot REC x1 or x2 only CD/MD MessagesCannot REC x1 REC only Message Troubleshooting SymptomSpecifications Amplifier Section-CA-UXZ7MDVictor Company of JAPAN, Limited