JVC LVT0900-003A manual Switching to a Program Type of Your Choice Temporarily, TA News, Info

Page 25

To continue searching after the first stop, press PTY

SEARCH again (while holding RDS CONTROL) when the selected PTY code in the main display is flashing.

To stop searching any time during the process, press

PTY SEARCH (while holding RDS CONTROL) when searching.

Switching to a Program Type of Your Choice Temporarily

The Enhanced Other Networks function allows the unit to switch temporarily to a broadcast program of your choice (TA, News, or Info) from a different station except when you are listening to a non-RDS station—some FM stations and AM (MW/LW) stations.

•Enhanced Other Networks function is applicable only to the preset stations.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the remote control ONLY:

1 While listening to an FM station, press and hold RDS CONTROL until you finish the following procedure.

2 Press TA/News/Info.

“EON SELECT” appears in the main display.

3 Press PTY SELECT + or – to select the Enhanced Other Networks data type you want.

The name of the selected Enhanced Other Networks data type starts flashing in the main display.

•Each time you press the button, the Enhanced Other Networks data types change as follows:

TA News

 

 

 

OFF

 

Info

 

 

 

 

 

 

 

 

 

 

(canceled)

 

 

 

TA:

Traffic announcement

News:

News

 

 

 

Info:

Programs the purpose of which is to impart

 

advice in the widest sense.

OFF:

The Enhanced Other Networks function is

 

canceled.

 

 

 

4 Press TA/News/Info again.

The indication disappears.

Now, this function is activated. See “How the Enhanced Other Networks function actually works” below.

5 Release your finger from RDS CONTROL.

To cancel the Enhanced Other Networks function, select “OFF” in step 3.

•If you cancel the Enhanced Other Networks function while receiving a program selected by the Enhanced Other Networks function, the unit goes back to the previously tuned station.

•The Enhanced Other Networks function is canceled when you change the source to “CD,” “MD” or “TAPE,” while it is temporarily canceled when you change the source to “AM.”

•The Enhanced Other Networks function is also canceled when you turn off the unit.

How the Enhanced Other Networks function actually works:

CASE 1

If there is no station broadcasting the program you have selected

The unit continues tuning in to the current station.

«

When a station starts broadcasting the program you have selected, the unit automatically switches to the station. The received PTY code starts flashing in the main display.

«

When the program is over, the unit goes back to the previously tuned station, but the Enhanced Other Networks function still remains activated.

CASE 2

If there is a station broadcasting the program you have selected

The unit tunes in to the program. The received PTY code starts flashing in the main display.

«

When the program is over, the unit goes back to the previously tuned station, but the Enhanced Other Networks function still remains activated.

– 20 –

Page 24 Page 26
Image 25
Page 24 Page 26
Contents LVT0900-003A UX-Z7MDR-Consists of CA-UXZ7MDR and SP-UXZ7MDIf in Doubt Consult a Competent Electrician UX-Z7MDR Important for Laser Products Above ALL Introduction PrecautionsContents Main Unit Location of the ButtonsMain unit Display window Display window on the electronic swing panelWhen using the remote control Remote ControlGetting Started Connecting AntennasUnpacking FM antennaYou can connect the speakers using the speaker cords Connecting SpeakersAM MW/LW antenna To connect an outdoor AM MW/LW antennaTo remove the speaker grilles Connecting External EquipmentTo connect external equipment Speaker grilles are removable as illustrated belowR6PSUM-3/AA15F Putting the Batteries into the Remote ControlBasic and Common Operations Remote controlSetting the Auto Power Off Turning On the PowerTurning On/Off the Key-touch Tone To turn off the clock indication power save mode Setting the ClockTo check the clock time with tones FM AM To increase the volume, turn Volume + / control ClockwiseIf Cannot Listen appears in the main display For private listeningFlat Jazz canceled Bass OFF canceledTo check the sound mode currently selected, press Reinforcing the Bass SoundTo select the illumination color Setting the Display IlluminationTo create your favorite colors To change the display brightnessListening to FM and AM MW/LW Broadcasts Presetting Stations Tuning in to a StationTo change the FM reception mode To change the information shown in the main displayReceiving FM Stations with RDS Tuning in to a Preset StationSearching for Programs by PTY Codes PTY Search Changing the RDS InformationPS PTY RT Release your finger from RDS Control Press PTY SearchTA News Switching to a Program Type of Your Choice TemporarilyInfo Test function Alarm functionDescription of the PTY codes Playing Back CDs CD-R/CD-RW Playing Back the Entire CD-Normal Play Precautions on CD PlaybackBasic CD Operations To go to another track directly using the number buttonsProgram Play To stop playback for a momentPlaying at Random-Random Play To check the program contentsRepeating Tracks-Repeat Play To modify the programPlaying Back MDs To locate a particular point in a track during play Basic MD OperationsWhile playing or pausing About MD indicatorNormal play MD Group On the main unit only To prohibit disc ejectionTo erase the entire program, press MD 0 to eject the MD On the remote control only Load an MD Press MD 3/8, thenTracks of the loaded MD will play at random Tracks are played at randomPlaying Tracks in a Group-Group Play MD Repeat OFF canceledPress Group Skip or Group Skip to select a group To go to another track in the same group, press ¢ orSearching for Tracks to Play MD Title Search Playing Back Tapes Playing Back a Tape To play both sides-Reverse modePush Push Open Put a cassette in with the exposed part of the tape downListening to External Equipment For how to apply sound effects, see Adjusting the Audio Input LevelListening to External Equipment Recording About the track marks Before You Start Recording on an MDTo avoid erasing important recordings To put a track mark manually while recording anStereo Long-Hour Recording Mdlp Precautions for performing long-hour stereo recordingAbout High-Speed Recording To check the remaining recording timeTo set the recording length mode Setting MD Recording ModesTo set LP-prefix addition mode To set Group recording modeRecording Other Sources onto an MD On the remote control only Press DISP/CHARATo record a single track during play or pause To record a tapeBefore You Start Recording on a Tape To clean the heads, capstans, and pinch rollersTo protect your recordings To keep the best recording and playback sound qualityTo record a single track of a CD/MD during play Recording onto a TapePrepare the source to record To record a disc To record an MDWhen recording on an MD and a tape at the same time Press REV.MODE to select the reverse modeFor the tape Press MD&TAPE RECEditing MDs How to make up Groups Using MD Group functionsGuidance-MD Group Functions Classifying the tracks on an MDIntroducing Group Editing Functions Press SET During playback Forming a Group-FORM GRPress ¢or 4to select the first track of a new group Press ¢or 4to select the last track of the new groupAdding a Track to a Group-ENTRY GR When Cannot ENTRY! appears in stepPress ¢or 4to select the track Or Group SkipTo join the divided groups again, see the Join GR Dividing a Group-DIVIDE GRFunction on Joining Two Groups-JOIN GR When Cannot Join appears in stepTo divide the group again, see the Divide GR function Moving a Group-MOVE GR Ungrouping Tracks-UNGROUP To cancel the setting, press CancelDissolving All Groups-UNGR ALL Erasing Tracks in a Group-ERASE GR Introducing Track Editing Functions Dividing a Track-DIVIDE Press or to precisely adjust the dividing pointPress ¢or 4to select the track you want to divide To join the divided tracks again, see the Join functionJoining Two Tracks-JOIN When the track belongs to a groupTo divide the joined tracks, see the Divide function on If Cannot Join appears in stepPress ¢or 4to select the track you want to move Moving a Track-MOVEErasing All Tracks-ALL Erase Erasing Tracks-ERASEPress SET Press ¢or 4to select the track you want to erase Assigning Titles to an MD Press or to change the title entry modeFor the group title For the disc and track titleChanging the Title Using the Timers How Recording Timer actually works Using Recording TimerSource indication Clock time canceled FM AM AUXHow Daily Timer actually works Using Daily TimerTo turn off the Recording Timer after its setting is done To turn on the Recording Timer againTo turn off the Daily Timer after its setting is done Volume setting appears in the main displayTo turn on the Daily Timer again FM AM CD AUX Tape MDTimer Priority Using Sleep TimerHow Sleep Timer actually works Maintenance Additional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Scms Serial Copy Management System Symptoms CauseHcms High-speed Copy Management System MD limitationsCannot REC x1 REC only CD/MD MessagesCannot REC x1 or x2 only Message Symptom TroubleshootingAUX/DVD Specifications0602MWMMDWJEM

LVT0900-003A specifications

The JVC LVT0900-003A is a remarkable car stereo designed to enhance the in-vehicle audio experience. Aimed at audiophiles and casual listeners alike, this model showcases JVC's commitment to delivering high-quality sound performance, robust build quality, and user-friendly features.

One of the standout attributes of the LVT0900-003A is its powerful amplification capabilities. With a built-in MOSFET amplifier, this stereo delivers clear and distortion-free sound, ensuring that even at higher volumes, the audio quality remains pristine. The unit is capable of supporting high-output speakers, making it a versatile choice for users who wish to upgrade their vehicle’s sound system.

The LVT0900-003A supports a wide range of media formats, including CDs, MP3s, and various digital audio files. This all-in-one capability allows users to enjoy their favorite music without the need for additional equipment. Additionally, the stereo features USB input and an auxiliary input, giving users the flexibility to connect smartphones, flash drives, and other external devices seamlessly.

In terms of connectivity, the LVT0900-003A is equipped with Bluetooth technology, enabling hands-free calling and wireless audio streaming. This feature not only enhances convenience for drivers but also promotes safety by allowing users to keep their hands on the wheel while taking calls or changing tracks.

Another notable characteristic of the JVC LVT0900-003A is its compatibility with various audio enhancement technologies. The stereo includes a built-in equalizer, allowing users to customize their sound preferences by adjusting the bass, midrange, and treble levels. This feature ensures a tailored listening experience that meets individual user needs.

The design of the LVT0900-003A is both sleek and practical, featuring a user-friendly interface with easy access to controls. The backlit display offers clear visibility in various lighting conditions, ensuring that drivers can effortlessly navigate through their audio options while on the road.

In conclusion, the JVC LVT0900-003A is a feature-rich car stereo that combines powerful audio performance with versatile connectivity options. Its blend of modern technology, user-friendly interface, and customizable sound settings make it an attractive option for anyone looking to enhance their in-car audio experience. With its robust build and quality engineering, the LVT0900-003A is sure to satisfy even the most discerning audio enthusiasts.
Top Page Image Contents