JVC LVT0900-003A manual Erasing Tracks-ERASE, Erasing All Tracks-ALL Erase

Page 63

Erasing Tracks—ERASE

This function allows you to erase unwanted tracks. You cannot resume the erased tracks.

Once tracks are erased, the other tracks and/or groups are renumbered.

You can erase up to 15 tracks at a time.

•To stop any time during the editing process before step 8, press TITLE/EDIT.

On the remote control ONLY:

In the following example, the process is explained from the very first—that is, inserting a disc. You can also edit an MD during playback (in Normal play mode).

1 Insert an MD you want to edit into the MD loading slot.

2 Press TITLE/EDIT repeatedly until “ERASE?” appears in the main display.

•If the loaded MD has no track, “ERASE?” will not appear.

•If you want to stop this editing process, press

CANCEL.

3 Press SET.

4 Press ¢or 4to select the track you want to erase.

•You can select the track using the number buttons. In this case, the selected track starts playing repeatedly.

5 Press SET.

“ ” appears in the main display.

The track marked with “ ” will be erased.

Ex.: When track 5 is selected.

•When you do not want to erase the track, press CANCEL to remove “ .”

6 Repeat steps 4 and 5 to select all the tracks you want to erase.

•You can select up to 15 tracks. If you select a 16th track to erase, “MEMORY FULL” will appear in the main display.

7 Press ENTER.

8 Press ENTER.

“EDITING” appears in the main display for a while, then “WRITING” and the MD REC indicator flash while the editing you have made is being recorded on the MD.

Erasing All Tracks—ALL ERASE

This function allows you to erase all the tracks on an MD. You cannot resume the erased tracks.

On the remote control ONLY:

In the following example, the process is explained from the very first—that is, inserting a disc. You can also edit an MD during playback (in Normal play mode).

1 Insert an MD you want to edit into the MD loading slot.

2 Press TITLE/EDIT repeatedly until “ALL ERASE?” appears in the main display.

•If you want to stop this editing process, press

CANCEL.

3 Press SET.

• To cancel the setting, press CANCEL.

4 Press ENTER.

“EDITING” appears in the main display for a while, then “WRITING” and the MD REC indicator flash while the editing you have made is being recorded on the MD.

“BLANK DISC” appears in the main display.

– 58 –

Page 62 Page 64
Image 63
Page 62 Page 64
Contents LVT0900-003A UX-Z7MDR-Consists of CA-UXZ7MDR and SP-UXZ7MDIf in Doubt Consult a Competent Electrician UX-Z7MDR Important for Laser Products Above ALL Introduction PrecautionsContents Location of the Buttons Main UnitMain unit Display window Display window on the electronic swing panelWhen using the remote control Remote ControlFM antenna Connecting AntennasGetting Started UnpackingTo connect an outdoor AM MW/LW antenna Connecting SpeakersYou can connect the speakers using the speaker cords AM MW/LW antennaSpeaker grilles are removable as illustrated below Connecting External EquipmentTo remove the speaker grilles To connect external equipmentR6PSUM-3/AA15F Putting the Batteries into the Remote ControlBasic and Common Operations Remote controlTurning On the Power Setting the Auto Power OffTurning On/Off the Key-touch Tone Setting the Clock To turn off the clock indication power save modeTo check the clock time with tones For private listening To increase the volume, turn Volume + / control ClockwiseFM AM If Cannot Listen appears in the main displayReinforcing the Bass Sound Bass OFF canceledFlat Jazz canceled To check the sound mode currently selected, pressTo change the display brightness Setting the Display IlluminationTo select the illumination color To create your favorite colorsListening to FM and AM MW/LW Broadcasts To change the information shown in the main display Tuning in to a StationPresetting Stations To change the FM reception modeReceiving FM Stations with RDS Tuning in to a Preset StationRelease your finger from RDS Control Press PTY Search Changing the RDS InformationSearching for Programs by PTY Codes PTY Search PS PTY RTSwitching to a Program Type of Your Choice Temporarily TA NewsInfo Alarm function Test functionDescription of the PTY codes Playing Back CDs CD-R/CD-RW Playing Back the Entire CD-Normal Play Precautions on CD PlaybackTo stop playback for a moment To go to another track directly using the number buttonsBasic CD Operations Program PlayTo modify the program To check the program contentsPlaying at Random-Random Play Repeating Tracks-Repeat PlayPlaying Back MDs To locate a particular point in a track during play Basic MD OperationsOn the main unit only To prohibit disc ejection About MD indicatorWhile playing or pausing Normal play MD GroupTracks are played at random On the remote control only Load an MD Press MD 3/8, thenTo erase the entire program, press MD 0 to eject the MD Tracks of the loaded MD will play at randomTo go to another track in the same group, press ¢ or MD Repeat OFF canceledPlaying Tracks in a Group-Group Play Press Group Skip or Group Skip to select a groupSearching for Tracks to Play MD Title Search Playing Back Tapes Put a cassette in with the exposed part of the tape down To play both sides-Reverse modePlaying Back a Tape Push Push OpenListening to External Equipment Adjusting the Audio Input Level For how to apply sound effects, seeListening to External Equipment Recording To put a track mark manually while recording an Before You Start Recording on an MDAbout the track marks To avoid erasing important recordingsTo check the remaining recording time Precautions for performing long-hour stereo recordingStereo Long-Hour Recording Mdlp About High-Speed RecordingTo set Group recording mode Setting MD Recording ModesTo set the recording length mode To set LP-prefix addition modeTo record a tape On the remote control only Press DISP/CHARARecording Other Sources onto an MD To record a single track during play or pauseTo keep the best recording and playback sound quality To clean the heads, capstans, and pinch rollersBefore You Start Recording on a Tape To protect your recordingsTo record an MD Recording onto a TapeTo record a single track of a CD/MD during play Prepare the source to record To record a discPress MD&TAPE REC Press REV.MODE to select the reverse modeWhen recording on an MD and a tape at the same time For the tapeEditing MDs Classifying the tracks on an MD Using MD Group functionsHow to make up Groups Guidance-MD Group FunctionsIntroducing Group Editing Functions Press ¢or 4to select the last track of the new group Forming a Group-FORM GRPress SET During playback Press ¢or 4to select the first track of a new groupOr Group Skip When Cannot ENTRY! appears in stepAdding a Track to a Group-ENTRY GR Press ¢or 4to select the trackDividing a Group-DIVIDE GR To join the divided groups again, see the Join GRFunction on When Cannot Join appears in step Joining Two Groups-JOIN GRTo divide the group again, see the Divide GR function Moving a Group-MOVE GR To cancel the setting, press Cancel Ungrouping Tracks-UNGROUPDissolving All Groups-UNGR ALL Erasing Tracks in a Group-ERASE GR Introducing Track Editing Functions To join the divided tracks again, see the Join function Press or to precisely adjust the dividing pointDividing a Track-DIVIDE Press ¢or 4to select the track you want to divideIf Cannot Join appears in step When the track belongs to a groupJoining Two Tracks-JOIN To divide the joined tracks, see the Divide function onPress ¢or 4to select the track you want to move Moving a Track-MOVEErasing Tracks-ERASE Erasing All Tracks-ALL ErasePress SET Press ¢or 4to select the track you want to erase For the disc and track title Press or to change the title entry modeAssigning Titles to an MD For the group titleChanging the Title Using the Timers FM AM AUX Using Recording TimerHow Recording Timer actually works Source indication Clock time canceledTo turn on the Recording Timer again Using Daily TimerHow Daily Timer actually works To turn off the Recording Timer after its setting is doneFM AM CD AUX Tape MD Volume setting appears in the main displayTo turn off the Daily Timer after its setting is done To turn on the Daily Timer againUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Maintenance Atrac Adaptive TRansform Acoustic Coding/ATRAC3 Utoc User Table Of ContentsAdditional Information MD Disc TypesMD limitations Symptoms CauseScms Serial Copy Management System Hcms High-speed Copy Management SystemCD/MD Messages Cannot REC x1 REC onlyCannot REC x1 or x2 only Message Symptom TroubleshootingAUX/DVD Specifications0602MWMMDWJEM

LVT0900-003A specifications

The JVC LVT0900-003A is a remarkable car stereo designed to enhance the in-vehicle audio experience. Aimed at audiophiles and casual listeners alike, this model showcases JVC's commitment to delivering high-quality sound performance, robust build quality, and user-friendly features.

One of the standout attributes of the LVT0900-003A is its powerful amplification capabilities. With a built-in MOSFET amplifier, this stereo delivers clear and distortion-free sound, ensuring that even at higher volumes, the audio quality remains pristine. The unit is capable of supporting high-output speakers, making it a versatile choice for users who wish to upgrade their vehicle’s sound system.

The LVT0900-003A supports a wide range of media formats, including CDs, MP3s, and various digital audio files. This all-in-one capability allows users to enjoy their favorite music without the need for additional equipment. Additionally, the stereo features USB input and an auxiliary input, giving users the flexibility to connect smartphones, flash drives, and other external devices seamlessly.

In terms of connectivity, the LVT0900-003A is equipped with Bluetooth technology, enabling hands-free calling and wireless audio streaming. This feature not only enhances convenience for drivers but also promotes safety by allowing users to keep their hands on the wheel while taking calls or changing tracks.

Another notable characteristic of the JVC LVT0900-003A is its compatibility with various audio enhancement technologies. The stereo includes a built-in equalizer, allowing users to customize their sound preferences by adjusting the bass, midrange, and treble levels. This feature ensures a tailored listening experience that meets individual user needs.

The design of the LVT0900-003A is both sleek and practical, featuring a user-friendly interface with easy access to controls. The backlit display offers clear visibility in various lighting conditions, ensuring that drivers can effortlessly navigate through their audio options while on the road.

In conclusion, the JVC LVT0900-003A is a feature-rich car stereo that combines powerful audio performance with versatile connectivity options. Its blend of modern technology, user-friendly interface, and customizable sound settings make it an attractive option for anyone looking to enhance their in-car audio experience. With its robust build and quality engineering, the LVT0900-003A is sure to satisfy even the most discerning audio enthusiasts.
Top Page Image Contents