Service Manual
3 Troubleshooting
Table 3G (continued from previous page) Troubleshooting Chart - Fault Messages Displayed on Boiler Interface
FAULT | DESCRIPTION | CORRECTIVE ACTION |
| ||
Sensor Open |
| • Check the sensors and their associated wiring. | |||
(will require a manual |
| Repair or replace the sensor or wiring if damaged. | |||
reset once the condition | Either the inlet water or outlet water | • Measure the resistance of the sensors and compare | |||
has been corrected. Press | temperature sensor has been disconnected. | the resistance to the tables on page | 38 | of this | |
the RESET button on the |
| manual. |
|
| |
display to reset.) |
|
|
| ||
| • Replace the sensor if necessary. |
|
| ||
|
|
|
| ||
|
|
|
| ||
Sensor Shorted |
| • Check the sensors and their associated | wiring. | ||
| Repair or replace the sensor or wiring if damaged. | ||||
(will require a manual |
| ||||
Either the inlet water or outlet water | • Measure the resistance of the sensors and compare | ||||
reset once the condition | |||||
has been corrected. Press | temperature sensor has been shorted. | the resistance to the tables on page 38 of this | |||
the RESET button on the |
| manual. |
|
| |
display to reset.) |
| • Replace the sensor if necessary. |
|
| |
|
|
|
| ||
|
|
| |||
Flue Sensor |
| • Check the sensor and its associated wiring. Repair | |||
| or replace the sensor or wiring if damaged. |
| |||
Open |
| • Measure the resistance of the sensors and compare | |||
(will require a manual |
| ||||
The flue sensor has been disconnected or | the resistance to the tables on page 38 of this | ||||
reset once the condition | |||||
has been corrected. Press | removed from the flue. | manual. |
|
| |
the RESET button on the |
| • Replace the sensor in flue. |
|
| |
display to reset.) |
|
|
| ||
| • Replace the sensor if necessary. |
|
| ||
|
|
|
| ||
|
|
|
| ||
Flue Sensor |
| • Check the sensor and its associated wiring. | Repair | ||
Shorted |
| or replace the sensor or wiring if damaged. |
| ||
(will require a manual |
| • Measure the resistance of the sensors and compare | |||
reset once the condition | The flue sensor has been shorted. | the resistance to the tables on page 38 of this | |||
has been corrected. Press | |||||
the RESET button on the |
| manual. |
|
| |
display to reset.) |
| • Replace the sensor if necessary. |
|
| |
|
|
|
|
| |
| Sensors equipped with an internal limit (such | • Check the tank temperature. |
|
| |
Tank Open | as the Lochinvar Squire® Indirect Tank), the | • Repair or replace the sensor wiring if damaged. | |||
| limit has opened due to temperature (195°F) | • Replace the sensor if necessary. |
|
| |
| or the sensor has become disconnected. |
|
| ||
|
| • Check the wiring connections to switch. Wires should | |||
|
| be connected to the common and normally open | |||
|
| terminals. |
|
| |
|
| • Remove switch and check for blockage in the orifice. | |||
|
| • Vent/air intake lengths exceed the maximum allowed | |||
Blower Proving |
| lengths. Refer to Section 2 - General Venting of the | |||
| Crest Installation and Operation Manual for | ||||
Switch Open 1 |
| proper lengths. |
|
| |
(will require a manual | Blower proving pressure switch 1 contacts | • Check for obstruction or blockage in the vent/air | |||
reset once the condition | |||||
has been corrected. Press | are open. | intake pipes or at terminations. |
|
| |
• Inspect the burner. Reference page 34 of this manual | |||||
the RESET button on the |
| ||||
| for removal and cleaning procedures. | Replace if | |||
display to reset.) |
| ||||
| necessary. |
|
| ||
|
|
|
| ||
|
| • Verify combustion air blower 1 is operating. Replace if | |||
|
| necessary. |
|
| |
|
| • Inspect the heat exchanger. Reference page 35 of | |||
|
| this manual for removal and cleaning procedures. | |||
|
| • Faulty pressure switch. Replace switch. |
|
| |
|
|
|
|
|
48