JVC RX-8000VBK manual Digital Input Digital in Terminal Setting, Turn Source Selector until

Digital Input (DIGITAL IN) Terminal Setting

When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3/ 4).

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

When the DIGITAL 1 is set to “CDR”

2 CD 3 TV (or 4 DBS*) 4 MD Ò 2 CD 3 MD 4 DVD Ò

2 MD 3 TV (or 4 DBS*) 4 DVD Ò 2 CD 3 TV (or 4 DBS*) 4 DVD Ò (back to the beginning)

When the DIGITAL 1 is set to “TV” or “DBS”

2 CD 3 DVD 4 CDR	Ò	2 CD 3 DVD 4 MD Ò
2 CD 3 MD 4 CDR	Ò	2 MD 3 DVD 4 CDR Ò
(back to the beginning)

On the front panel ONLY:

To set the DIGITAL 1 terminal

1.Press SETTING repeatedly until “COAX. DIG. IN” appears on the

display.

The display changes to show the current setting.

2.Turn MULTI JOG to select the appropriate digital terminal setting.

SETTING

MULTI JOG

When the DIGITAL 1 is set to “CD”

2 MD 3 TV (or 3 DBS*) 4 CDR Ò

2 DVD 3 TV (or 3 DBS*) 4 CDR Ò 2 DVD 3 TV (or 3 DBS*) 4 MD Ò 2 DVD 3 MD 4 CDR Ò

(back to the beginning)

*If you have changed the source name from “TV SOUND” to “DBS,” “DBS” appears.

Note:

• As you turn it, the display changes to show the following:

1 DVD Ò1 MD Ò1 CDR Ò1 TV (or 1 DBS*) Ò 1 CD Ò(back to the beginning)

*If you have changed the source name from “TV SOUND” to “DBS,” “DBS” appears.

When shipped from the factory, the DIGITAL IN terminals can be used as the digital input for the following components.

•DIGITAL 1 (coaxial): For DVD player

•DIGITAL 2 (optical): For CD player

•DIGITAL 3 (optical): For digital TV broadcast tuner

•DIGITAL 4 (optical): For CD recorder

To set the DIGITAL 2/3/4 terminal

1.Press SETTING repeatedly until “OPT. DIG. IN” appears on the

display.

SETTING

Selecting the Analog or Digital Input

Mode

When you have connected digital source components using the digital terminals (see page 8), you need to change the input mode for these components to the appropriate digital input mode correctly —

The display changes to show the current setting.

DIGITAL 3 terminal setting

DIGITAL 2 terminal setting DIGITAL 4 terminal setting

MULTI JOG

2.Turn MULTI JOG to select the appropriate digital terminal settings.

•As you turn it, the display changes to show the following:

When the DIGITAL 1 is set to “DVD”

2 CD 3 MD 4 CDR Ò

2 MD 3 TV (or 2 DBS*) 4 CDR Ò 2 CD 3 TV (or 2 DBS*) 4 CDR Ò 2 CD 3 TV (or 2 DBS*) 4 MD Ò (back to the beginning)

When the DIGITAL 1 is set to “MD”

2 DVD 3 TV (or 2 DBS*) 4 CDR Ò 2 CD 3 TV (or 2 DBS*) 4 CDR Ò

2 CD 3 TV (or 2 DBS*) 4 DVD Ò 2 CD 3 DVD 4 CDR Ò

(back to the beginning)

AUTO/PCM, DOLBY DIGITAL, or DTS.

Before you start, remember...

•The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.

On the front panel:

1. Turn SOURCE SELECTOR until	SOURCE SELECTOR
the source (CD, MD, TV SOUND,
DBS, DVD, or CDR/VCR2)* for
which you want to change the
input mode appears on the display.

Note:

*Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)

16