ProForm PFTL99220 user manual Troubleshooting, Solution, Power Cord

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-

free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, please call our Customer Service Department.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION:

a. With the key in the console, press one of the Incline buttons.

While the incline is changing, re-

 

move the key.

After a few seconds, re-insert the key. The treadmill will automatically rise to the

 

maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The console is too high or too low

SOLUTION: a. See assembly step 7 on page 7.

PROBLEM: The treadmill rocks during use

SOLUTION: a. See HOW TO LEVEL THE TREADMILL on page 20.

PROBLEM: The displays of the console do not function properly

SOLUTION:

a. Remove the key from the console and

UNPLUG THE

 

POWER CORD.

With the help of a second person,

carefully tip the Upright Base (97) down as shown. Remove the five Hood Screws (44). Note: A phillips screwdriver with at least a 5” shaft is required.

a

44

 

 

97

44

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents To Avoid QUESTIONS?Model No. PFTL99220 Serial No Customer HOT LineTable of Contents Important PrecautionsCD player or VCR when you are not using them Never insert any object into any openingRight Side Using the treadmillBefore YOU Begin BackDecal 91 is in the indicated location AssemblyMake sure that the power cord is unplugged WayPlace Uprights. Retighten all four Upright Bolts Console 107 as shownImportant Never apply silicone spray or other HOW to Plug in the Power CordPerformant Lube This product must be grounded.If it should malfuncCDs, call toll-free Features of the ConsolePrograms HOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired See page 20 and turn off the demo modePlay Next, stand on Foot railsPress the Start button or the Speed HOW to USE Preset ProgramsSelect one of the preset programs Start the programFollow your progress with the displays You have not entered your age, press Enter your age and a maximum speed settingHave already entered Turn on the fans if desiredPress the Play/Pause button to start Program Next settings of the CD programAdjust the volume if desired Button or the SpeedFollow your progress with the track Displays HOW to Play Music CDSUAL Mode on page 10. Note Due to the nature Whenkey. the program is completed, removeHOW to Connect the Treadmill to Your VCR or Computer HOW to Connect the Treadmill to Your ComputerFor speed Press the Play button on your VCRTreadmill is about to change Console. HoweverWhen the program has ended, remove the key HOW to USE Programs Directly from OUR WEB SiteNext settings of the program Follow the on-line instructions to start ProgramButtons on the console will not operate Information MODE/DEMO ModeHOW to Level the Treadmill So the display is blankHOW to Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Lower the Treadmill for USE Solution TroubleshootingPower Cord If the walking Problem The walking belt slows when walked onCome damaged. Remove the key Belt has shifted to the leftWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Washer Photo Switch WireDescription Internal Star WasherBlack Wire, M/F Part Identification Chart113 Red Wire, M/F 114 Motor Bracket Bolt 101 Console Base 120 Right Handgrip 102 121DRAWING-Model R0903A109 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT HOW to Order Replacement PartsLimited Warranty Part No R0903A
Top Page Image Contents