ProForm PCTL79612.0 user manual Top View, Symptom The walking belt slows when walked on

Page 27

Locate the Reed Switch (52) and the Magnet (50) on the left side of the Pulley (49). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Tek Screw (14), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown) and run the treadmill for a few minutes to check for a correct speed reading.

b.If the walking belt is overtightened, treadmill per- formance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

Top

View

52

14

1/8 in.

49

50

b

2–3 in.

Idler Roller Screws

SYMPTOM: The incline of the treadmill does not change correctly

a.Hold down the Stop button and the Speed increase button, insert the key into the console, and then release the Stop button and the Speed increase button. Press the Stop button and then press the Incline increase or decrease button. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system. If the incline does not begin calibrating, press the Stop button again, and then press the Incline increase or decrease button again. When the incline is calibrated, remove the key from the console.

SYMPTOM: The walking belt slows when walked on

a.Use only a surge suppressor that meets all of the specifications described on page 15.

c.Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deterio- rate the walking belt and cause excessive wear. If you suspect the walking belt needs more lubri- cant, see the front cover of this manual.

d.If the walking belt still slows when walked on, see the front cover of this manual.

27

Image 27
Contents Model No. PCTL79612.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Part Identification Chart Make sure that the power cord is unplugged AssemblySee the inset drawing. Tie the wire tie Be careful not to pinch the Upright WireTighten the Screws yet Attach the Right Upright not shown Base Covers into place yet Shown. Start all four Screws, and then tighten Them 113 Console Assembly Make sure to follow All instructions This step Raise the Frame 56 to the position shown Operation and Adjustment HOW to Connect the Power CordUse a Surge Suppressor Diagram Features of the ConsoleConsole Insert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeChange the incline of the treadmill as desired Calories/InclineTime display Turn on the fan if desired Measure your heart rate if desiredHOW to USE AN Onboard Workout Select an onboard workoutStart the workout Start the workout. See on HOW to USE AN Ifit Live WorkoutInsert the iFit Live module into the console Select an iFit Live workoutHOW to USE a Proform Sync Select the optional screens Information ModeSelect the information mode Exit the information modeMake sure that the iPod is fully plugged HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillSymptom The power turns off during use TroubleshootingTop View Symptom The walking belt slows when walked onPage Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description Part ListDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement Parts