ProForm 7 manual Bolts yet

Page 8

4.Hold a Bolt Spacer (79) inside the lower end of the Right Upright (78). Insert an M10 x 96mm Bolt (5) with an M10 Star Washer (8) into the Right Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (79), M10 x 96mm Bolt (5), and M10 Star Washer (8). Hold the Right Upright (78) against the Right Upright Spacer (80). Be careful not to pinch the Upright Wire (77). Partially tighten the M10 x 96mm Bolts (5); do not fully tighten the

Bolts yet.

Press a Base Endcap (82) into the Base (85).

5.With the help of a second person, carefully tip the treadmill onto its right side. Partially fold the Frame (48) so the treadmill is more stable; do not fully fold the Frame yet.

Remove and discard the two indicated bolts (A) and the shipping bracket (B).

Attach a Base Pad (81) to the Base (85) in the location shown with a Base Pad Spacer (104) and an M4.2 x 25mm Tek Screw (2). Then, at- tach a Base Pad (81) in the location shown with only an M4.2 x 25mm Tek Screw (2).

Remove the M10 Nut (33), the M10 x 50mm Bolt (4), and the shipping bracket (C) from the Base (85). Attach a Wheel (86) with the Bolt and the Nut that you just removed. Do not over- tighten the Nut; the Wheel must turn freely. Discard the shipping bracket.

4			5
		78	5
		78		8 77
				8 77		79
				8079		82
				85
5	A	B
		B

2	81			48	4
2	81	104			4
	85	104		86
	85	2	81		C
		2	81
				33

8

Image 8

Contents Contact OUR Customer SER- Vice Department Directly QUESTIONS?Model No. PCTL57809.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Nut the Wheel must turn freely. Discard Make sure that the power cord is unpluggedDo not fully fold the Frame yet Bolts yet Save all six Screws for . Lift off the Pulse Support Console Assembly 109 Ground Wire Again. if the Connectors are not CON Be Damaged When the Power isThat no wires are pinched Nected PROPERLY, the Console MAYMake sure that no wires are pinched PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power Select the user modeSelect a default user setting Set the date and timeHOW to Identify Yourself AS User 1 or User HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleMeasure your heart rate if desired HOW to USE a Personal Trainer Workout Select a personal trainer workoutHOW to View the Fitness Journal HOW to Reset the Fitness Journal Select the user mode. See on Reset the fitness journalExit the user mode HOW to USE the Stereo Sound SystemInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Problem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part LIST-Model No. PCTL57809.0 Key No. Qty DescriptionKey No. Qty Description Exploded Drawing A-Model No. PCTL57809.0 R0909A Exploded Drawing B-Model No. PCTL57809.0 R0909A Exploded Drawing C-Model No. PCTL57809.0 Exploded Drawing D-Model No. PCTL57809.0 R0909A Ordering Replacement Parts Limited Warranty