ProForm PFEL25070 user manual Electronic Monitor TROUBLE-SHOOTING, HOW to Adjust the Reed Switch

Page 9

ELECTRONIC MONITOR TROUBLE-SHOOTING

If the console does not function properly, the batteries should be replaced. To replace the batteries, see assembly step 7 on page 8. In addition, make sure that the console wire is connected to the extension wire. See assembly step 6 on page 7.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the reed switch should be adjusted. In order to adjust the reed switch, the Left Side Shield (5) must be removed. Remove the 1/2Ó Nylon Locknut (37) from the Pedal Bolt (36). Turn the Pedal Bolt and remove it from the Crank (38); do not remove the Pedal Bolt from the Left Pedal Arm (7). Set the Left Pedal Arm aside.

 

Top

 

5

 

 

 

 

 

37

Rear

 

 

 

 

 

 

38

 

 

 

66

36

7

 

 

 

 

 

 

 

 

66

Remove the three M4 x 38mm Screws (66) from the bottom of the Left Side Shield (5). Grasp both Side Shields at the top and gently pull them apart. Make sure that the arm of the Crank (38) is in the position shown in the drawing above. Hold the Left Side Shield at the rear and pull it gently away from the frame. Work the Left Side Shield forward off the arm of the Crank and remove it.

Next, locate the

 

Reed Switch (3).

 

Loosen, but do

 

not remove, the

 

M4 x 16mm

38

Screw (51).

3

 

Slide the Reed

51

Switch slightly

 

toward or away

Magnet

from the magnet

 

on the pulley.

 

Retighten the

 

Screw. Turn the Crank (38) for a moment. Repeat until

the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the left side shield.

HOW TO ADJUST THE TENSION BELT

If the pedals do not have enough resistance, even when the pedal resistance knob is turned to the maxi- mum setting, the Resistance Belt (24) may need to be adjusted. To adjust the Resistance Belt, the left side shield must be removed. Refer to the instructions at the left to remove the left side shield.

Next, turn the

 

pedal resistance

Latch

knob to its low-

 

est setting.

49

Locate and

 

open the latch

 

on the Resis-

 

tance Belt

24

Clamp (49).

38

Grip the end of

 

the Resistance

 

Belt (24) and

 

pull it down to remove any slack. While holding the end of the Tension Belt, close the latch on the Tension Belt Clamp. Turn the Crank (38) for a moment to make sure that there is not too much resistance. When the resistance strap is properly adjusted, reat- tach the left side shield.

9

Image 9
Contents Model No. PFEL25070 Serial No QUESTIONS?Customer HOT Line Mon.ÐFri., 6 a.m.Ð6 p.m. MSTTable of Contents Important Precautions Before YOU Begin FrontBack Right Side Part Identification Chart Assembly Page Lubricating the Handlebars MaintenanceElectronic Monitor TROUBLE-SHOOTING HOW to Adjust the Reed SwitchHOW to Adjust the Tension Belt HOW to Exercise on the L.E.X HOW to USE the PROFORM¨ L.E.XHOW to Adjust the Resistance of the Pedals HOW to USE the Handlebars in the Stationary PositionDescription of the Console Diagram of the ConsoleHOW the Pacer Programs Operate Description of the Monitor ModesSTEP-BY-STEP Console Operation Select one of the three pacer programs or Manual modeBegin your workout Follow your progress with the monitor modesHOW to Measure Your Heart Rate WHY EXERCISE?Conditioning Guidelines Exercise IntensityQty Description Exercise FrequencyExploded DRAWINGÑModel No. PFEL25070 HOW to Order Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT