JVC RX-8022PSL manual USB Connection, Lamp on the USB Audio button on the front panel lights up

Page 17

USB Connection

This receiver is equipped with a USB terminal on the front panel. You can connect your PC to this terminal and enjoy sound reproduced through your PC.

When you connect your PC for the first time, follow the procedure below.

Remember you cannot send any signal or data to your PC from this receiver.

IMPORTANT:

Check if your PC equipped with the CD-ROM drive is running on WindowsR 98*, WindowsR Me* or WindowsR XP* and prepare its CD-ROM.

Check your PC’s BIOS setting—whether USB is available, and whether USB IRQ is set to “AUTO” or to available IRQ number.

How to install the USB drivers

The following procedure is described using the English version of WindowsR 98. If your PC is running on a different version of operation system or language, the screens shown on your PC’s monitor will differ from the ones used in the following procedure.

1.Turn on your PC and start running WindowsR 98, WindowsR Me or WindowsR XP.

If the PC has been turned on, quit all the applications now running.

2.Turn on the receiver, and press USB AUDIO on the front panel or USB on the remote control.

The lamp on the USB AUDIO button on the front panel lights up.

3.Connect the receiver to the PC using a USB cable (not supplied).

Your PC automatically recognizes this connection, and shows

the following screen on the monitor.

USB AUDIO

VIDEO

 

 

 

 

 

 

S-VIDEO

VIDEO

L—AUDIO—R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PC

USB cable (not supplied)

4.Install the USB drivers following the instructions shown on the PC’s monitor.

5.Check if the drivers are correctly installed.

1.Open the Control Panel on your PC: Select [Start] = [Settings] = [Control Panel].

2.Select [System], then [Device Manager] and click [Sound, video and game controllers] and [Universal serial bus controller].

The following window appears, and you can check whether the drivers are installed.

Note:

The items shown on the PC’s monitor differ depending on

your PC settings.

6.Change the PC audio setting.

1.If you have closed Control Panel, open it again: Select [Start] = [Settings] = [Control Panel].

2.Click [Multimedia], then select “USB Audio Device [1]” for “Playback” of “Audio,” and close the window.

To play back a CD from CD-ROM drive on PC, click [Multimedia], [CD Music], then check [Enable digital CD audio for this CD-ROM device].

Now PC is ready for playback through the USB connection.

After installation is completed, you can use your PC as the playback source. The PC automatically recognizes the receiver whenever a USB cable is connected between the PC and the receiver while the receiver is turned on.

When not using the PC as the playback source, disconnect the USB cable.

To play back sounds on the PC, refer to the manuals supplied with the sound reproduction application installed in the PC.

Notes:

DO NOT turn off the receiver or disconnect the USB cable while installing the drivers and for several seconds while your PC is recognizing the receiver.

Use a full speed USB cable (revision 1.0). Recommended cord length is 1.5 m.

If your PC does not recognize the receiver, disconnect the USB cable and connect it again. If it does not work yet, restart Windows.

The installed drivers can be recognized only when the USB cable is connected between the receiver and your PC.

The sound may not be played back correctly—interrupted or degraded—due to your PC settings and PC specifications.

When you do not use the terminals on the front panel, attach the supplied front terminal cover to protect them from dust.

*Microsoft R, WindowsR 98, WindowsR Me and WindowsR XP are registered trademarks of Microsoft Corporation.

14

Image 17
Contents RX-8022PSL Page RX-8022PSL Table of Contents Introduction Features PrecautionsFront Panel Master Volume controlDisplay Window STANDBY/ON button and Standby lamp Speakers ON/OFF 1 buttonRemote control display window Remote ControlConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Setting the Voltage SelectorAM Antenna Connections Connecting the SpeakersBest reception Typical speaker layoutConnecting the front, center and surround speakers Basic connecting procedureConnecting the surround back speakers Connecting the subwoofer speakerEnhancing your audio system Connecting Audio/Video ComponentsAnalog Connections Audio component connectionsTo audio output CD playerCassette deck or MD recorder CD recorder To audio inputVideo component connections When attaching the coverVCRs VHS/VHS VCRDBS tuner TV and/or DBS tunerDVD player When you connect a DVD player with stereo output jacksDVD player Digital output terminal Digital ConnectionsDigital input terminals USB Connection Change the PC audio settingLamp on the USB Audio button on the front panel lights up USB cable not suppliedPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverBefore using the remote control Turning On the PowerBasic Operations Selecting the Source to PlaySpeaker indicators light up Speaker and signal indicators on the displayChanging the source name Selecting different sources for picture and soundSelecting the Front Speakers Adjusting the Volume Listening Only with HeadphonesHeadphone mode When selecting Dgtl D.D Selecting the Analog or Digital Input ModeWhen selecting Dgtl DTS Dgtl Auto appears on the displayBasic adjustment auto memory Using the Sleep TimerMuting the Sound Changing the Display BrightnessBasic Procedure Basic SettingsSetting the Speakers Measuring unit-DIST Unit Setting the Speaker DistanceFeet Select this to set the distance in feet Speaker distance-FRONT DIST, Center CntrSetting the Dynamic Range-MID Night Setting the Bass SoundsCrossover frequency-CROSSOVER Low frequency effect attenuator-LFE ATTDigital in 1-DVD, MD**, CDR, TV or DBS* or CD Setting the Digital Input Digital in TerminalsSetting the Component Video Input To recall the volume level Select this not to store the volume levelTo cancel the One Touch Operation Source name and Surround/DSP mode appearReceiving Radio Broadcasts Tuning into Stations Manually Using Preset TuningSelecting the FM Reception Mode Press FM/AM Preset 5 or ∞While listening to an FM station, press FM Mode To tune in a preset stationPress 5 or ∞ to move to an item you want to set or adjust Operating the Tuner Using the On-Screen DisplayStoring the preset stations Press 5 or ∞ to move to Tuner CONTROL, then press 2 orTurning Analog Direct On and Off Setting SoundAttenuating the Input Signal Press Bass Boost to turn on Bass Bass Boost Boost function Reinforcing the BassPress Sound Press Bass Boost to turn on BassReproducing Theater Ambience Introducing the Surround Modes Using Surround Modes and DSP ModesDolby Surround Movie theater At homeDTS Digital Surround DVD Multi Playback ModeNeo6 Music DTS-ESBehind 3D Headphone ModeEarly reflections Direct soundsDolby Digital 5.1-channel software Dolby Digital EX software Dolby D EXDTS-ES software DTS 5.1-channel software DTSOn the front panel From the remote control Press Surround to activate Surround modeActivating the Surround Modes Activating the DSP ModesPress DVD Multi so that DVD Multi appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Adjusting Sound Adjusting the Equalization Patterns Select this to adjust the subwoofer Adjusting the Speaker Output LevelsLevel Output levelPress Level + or to adjust Speaker output level -10 dB to Select a speaker you want to adjustPress Level Adjust repeatedly to Down ∞ to adjust the speakerParameter you want to adjust Show Effect Adjust menu seeDown ∞ to adjust the sound Press Effect repeatedly to select aPress the play 3 button on the CD player Compu Link Remote Control SystemSame time Functions Text Compu Link Remote Control SystemConnections Press Text Display while CD or MD is selected as the source On-Screen Operating buttons on the remote controlOperations Showing the Disc Information on the TV ScreenPress SET Press Text Display while CD is selected as the sourceThen press SET Press SET againEntering the Disc Information Press 5 or ∞ to move To SEARCH, then Press SETPress 5 or ∞ to move To GENRE, then Press SET Press 5 or ∞ to move to the genre you want, then press SET Press Text Display while MD is selected as the sourceEnter the disc title, referring to steps 3 Connections 1 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 2 Video Cable Connection VCR connected toAutomatic Power On/Off Automatic Selection of TV’s Input ModeOne-Touch Video Play One-Touch DVD PlayOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section AmplifierCD changer CD playerTurntable CD recorderDVD player Operating Video ComponentsVCR 1 VCR connected to the VCR 1 jacks Operating Other Manufacturers’ Video Equipment Enter a manufacturer’s code using buttons 1-9,Press and hold TV Press TV/DBS Release TVPress and hold CATV/DBS Press CATV/DBS Control Enter manufacturer’s code using buttons 1-9,Release CATV/DBS Press and hold VCR1 Press VCR1Release Audio Press and hold Audio Press DVDProblem Possible Cause Solution TroubleshootingProblem Amplifier SpecificationsAudio VideoFM tuner IHF Tuning Range Usable Sensitivity Signal-to-Noise RatioAM tuner GeneralElectric shock