JVC RX-8022PSL, LVT0870-006A manual Problem

Page 61

PROBLEM

“OVERLOAD” starts flashing on the display.

POSSIBLE CAUSE	SOLUTION
Speakers are overloaded because of	1.Press STANDBY/ON	on the front panel to
high volume.	turn off the receiver.
	2.Stop the playback source.
	3.Turn on the receiver again and adjust the volume.

Speakers are overloaded because of	Press STANDBY/ON	on the front panel to turn
short circuit of speaker terminals.	off the receiver, then check the speaker wiring.
	If “OVERLOAD” does not disappear, unplug the AC
	power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

The STANDBY lamp lights up after turning on the power, and soon the receiver turns off again (into standby mode).

The receiver is overloaded because of high voltage.

Press STANDBY/ON on the front panel to turn off the receiver. After unplugging the AC power cord, consult your dealer.

Remote control does not work.

There is an obstruction between the	Remove the obstruction.
remote sensor on the receiver and the
remote control.

Remote control does not work intendedly.

Batteries are weak.

An incorrect remote control operation mode is selected.

Replace batteries. (See page 15.)

Select the correct remote control operation mode. (See pages 51 to 53.)

58

Image 61

Contents RX-8022PSL Page RX-8022PSL Table of Contents Introduction Features PrecautionsFront Panel Master Volume controlDisplay Window STANDBY/ON button and Standby lamp Speakers ON/OFF 1 buttonRemote control display window Remote ControlConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Setting the Voltage SelectorAM Antenna Connections Connecting the SpeakersBest reception Typical speaker layoutConnecting the front, center and surround speakers Basic connecting procedureConnecting the surround back speakers Connecting the subwoofer speakerEnhancing your audio system Connecting Audio/Video ComponentsAnalog Connections Audio component connectionsTo audio output CD playerCassette deck or MD recorder CD recorder To audio inputVideo component connections When attaching the coverVCRs VHS/VHS VCRDBS tuner TV and/or DBS tunerDVD player When you connect a DVD player with stereo output jacksDVD player Digital input terminals Digital ConnectionsDigital output terminal USB Connection Change the PC audio settingLamp on the USB Audio button on the front panel lights up USB cable not suppliedPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverBefore using the remote control Turning On the PowerBasic Operations Selecting the Source to PlaySpeaker indicators light up Speaker and signal indicators on the displayChanging the source name Selecting different sources for picture and soundHeadphone mode Adjusting the Volume Listening Only with HeadphonesSelecting the Front Speakers When selecting Dgtl D.D Selecting the Analog or Digital Input ModeWhen selecting Dgtl DTS Dgtl Auto appears on the displayBasic adjustment auto memory Using the Sleep TimerMuting the Sound Changing the Display BrightnessBasic Procedure Basic SettingsSetting the Speakers Measuring unit-DIST Unit Setting the Speaker DistanceFeet Select this to set the distance in feet Speaker distance-FRONT DIST, Center CntrSetting the Dynamic Range-MID Night Setting the Bass SoundsCrossover frequency-CROSSOVER Low frequency effect attenuator-LFE ATTSetting the Component Video Input Setting the Digital Input Digital in TerminalsDigital in 1-DVD, MD**, CDR, TV or DBS* or CD To recall the volume level Select this not to store the volume levelTo cancel the One Touch Operation Source name and Surround/DSP mode appearReceiving Radio Broadcasts Tuning into Stations Manually Using Preset TuningSelecting the FM Reception Mode Press FM/AM Preset 5 or ∞While listening to an FM station, press FM Mode To tune in a preset stationPress 5 or ∞ to move to an item you want to set or adjust Operating the Tuner Using the On-Screen DisplayStoring the preset stations Press 5 or ∞ to move to Tuner CONTROL, then press 2 orAttenuating the Input Signal Setting SoundTurning Analog Direct On and Off Press Bass Boost to turn on Bass Bass Boost Boost function Reinforcing the BassPress Sound Press Bass Boost to turn on BassReproducing Theater Ambience Introducing the Surround Modes Using Surround Modes and DSP ModesDolby Surround Movie theater At homeDTS Digital Surround DVD Multi Playback ModeNeo6 Music DTS-ESBehind 3D Headphone ModeEarly reflections Direct soundsDolby Digital 5.1-channel software Dolby Digital EX software Dolby D EXDTS-ES software DTS 5.1-channel software DTSOn the front panel From the remote control Press Surround to activate Surround modeActivating the Surround Modes Activating the DSP ModesActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the display Adjusting Sound Adjusting the Equalization Patterns Select this to adjust the subwoofer Adjusting the Speaker Output LevelsLevel Output levelPress Level + or to adjust Speaker output level -10 dB to Select a speaker you want to adjustPress Level Adjust repeatedly to Down ∞ to adjust the speakerParameter you want to adjust Show Effect Adjust menu seeDown ∞ to adjust the sound Press Effect repeatedly to select aSame time Compu Link Remote Control SystemPress the play 3 button on the CD player Connections Text Compu Link Remote Control SystemFunctions Press Text Display while CD or MD is selected as the source On-Screen Operating buttons on the remote controlOperations Showing the Disc Information on the TV ScreenPress SET Press Text Display while CD is selected as the sourceThen press SET Press SET againPress 5 or ∞ to move To GENRE, then Press SET Press 5 or ∞ to move To SEARCH, then Press SETEntering the Disc Information Enter the disc title, referring to steps 3 Press Text Display while MD is selected as the sourcePress 5 or ∞ to move to the genre you want, then press SET Connections 1 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 2 Video Cable Connection VCR connected toAutomatic Power On/Off Automatic Selection of TV’s Input ModeOne-Touch Video Play One-Touch DVD PlayOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section AmplifierCD changer CD playerTurntable CD recorderVCR 1 VCR connected to the VCR 1 jacks Operating Video ComponentsDVD player Operating Other Manufacturers’ Video Equipment Enter a manufacturer’s code using buttons 1-9,Press and hold TV Press TV/DBS Release TVPress and hold CATV/DBS Press CATV/DBS Control Enter manufacturer’s code using buttons 1-9,Release CATV/DBS Press and hold VCR1 Press VCR1Release Audio Press and hold Audio Press DVDProblem Possible Cause Solution TroubleshootingProblem Amplifier SpecificationsAudio VideoFM tuner IHF Tuning Range Usable Sensitivity Signal-to-Noise RatioAM tuner GeneralElectric shock