JVC RX-7020VBK manual Connecting the Power Cord, Digital connections, Digital output terminal

Page 11

Digital connections

This receiver is equipped with four DIGITAL IN terminals — one digital coaxial terminal and three digital optical terminals, and one DIGITAL OUT terminal.

You can connect any digital equipments such as — :

•DBS tuner,

•Digital TV broadcast tuner,

•DVD player,

•CD player, and

•CD recorder.

IMPORTANT:

•When connecting the DVD player, digital TV broadcast tuner or DBS tuner using the digital terminals, you also need to connect it to the video jack on the rear. Without connecting it to the video jack, you can view no playback picture.

•After connecting the components using the DIGITAL IN terminals, set the following correctly if necessary:

–Set the digital input (DIGITAL IN) terminal setting correctly. For details, see “Setting the Digital Input (DIGITAL IN) Terminals” on page 14.

–Select the digital input mode correctly. For details, see “Selecting the Analog or Digital Input Mode” on page 15.

Notes:

•When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components:

–DIGITAL 1 (coaxial): For DVD player

–DIGITAL 2 (optical): For CD player

–DIGITAL 3 (optical): For digital TV broadcast tuner

–DIGITAL 4 (optical): For CD recorder

•When you want to operate the CD player or CD recorder using the COMPU LINK remote control system, connect the target component also as described in “Analog connections” (see page 7).

•When you want to operate the DVD player using the AV COMPU LINK remote control system, connect the DVD player also as described in “Analog connections” (see page 8).

Digital output terminal

This terminal can output the same type of incoming signals Dolby Digital, Linear PCM, and DTS.

CD recorder, etc.

Getting Started

Digital input terminals

Digital TV

CD player

DBS tuner

DBS

DVD player

DVD

CD recorder

Digital optical cable (not supplied) between digital optical terminals

When the digital recording equipment such as a CD recorder has a digital optical input terminal, connect it to the DIGITAL OUT terminal enables you to perform

digital-to-digital recording.DOLBY DIGITAL/PCM

/DTS

DIGITAL OUT

Digital coaxial cable (not supplied) between digital coaxial terminals

Digital optical cable (not supplied) between digital optical terminals

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all connections have been made.

Plug the power cord into an AC outlet.

When the component has a digital coaxial output terminal, connect it to the DIGITAL 1 (DVD) terminal, using the digital coaxial cable (not supplied).

When the component has a digital optical output terminal, connect it to the DIGITAL 2 (CD), DIGITAL 3 (TV), or DIGITAL 4 (CDR) terminal, using the digital optical cable (not supplied).

Before connecting a digital optical cable, unplug the protective plug.

DIGITAL 1 (DVD)

DIGITAL 2 ( CD )

DIGITAL 3 ( TV )

DIGITAL 4 (CDR)

DOLBY DIGITAL

/PCM

/DTS

DIGITAL IN

Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

CAUTIONS:

•Do not touch the power cord with wet hands.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents RX-7020VBK For Canada/pour le Canada Mises en garde, précautions et indications diversesTable of Contents See pages in the parentheses for details Remote ControlParts Identification Front PanelReplace the cover Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedFM antenna connection Connecting the FM and AM AntennasGetting Started AM antenna connectionConnection diagram Connecting the SpeakersSpeaker layout diagram Connecting the front speakersAnalog connections Audio component connections Connecting Audio/Video ComponentsConnecting the rear and center speakers Connecting the subwoofer speakerVCR Video component connectionsCD player Cassette deck or CD recorderDBS tuner B When you connect the DVD player with stereo output jacksTV and/or DBS tuner DVD player DVD playerDigital output terminal Connecting the Power CordPlug the power cord into an AC outlet Digital connectionsSelecting the Source to Play Turning On the PowerTo turn off the power into standby mode Basic OperationsAdjusting the Volume Changing the Display Brightness Listening Only with HeadphonesTurning Off the Power With the Sleep Timer Basic OperationsSpeaker indicators light up when Basic adjustment auto memorySignal and speaker indicators on the display Signal indicators Speaker indicatorsDigital in Terminals Basic SettingsSetting the Digital Input Selecting the Analog or Digital Input Mode Setting the Speaker Information Remote Basic SettingsSpeaker size Unit with the current setting Appears on the displayPress Control UP 5/DOWN ∞ to select the unit Select the appropriate speaker distanceLevel Press Setting repeatedly until LFE T SettingSelect the low frequency effect attenuator level To select the appropriate compressionOutput Balance Sound AdjustmentsAdjusting the Front Speakers Reinforcing the Bass Sound AdjustmentsAdjusting the Tone Adjusting the Subwoofer Output LevelTuner Operations Tuning in Stations ManuallyUsing Preset Tuning Press FM/AM Preset 5/∞ toTuner Operations Selecting the FM Reception ModeTypical Multichannel 5.1 ch reproduction Creating Realistic Sound FieldsDolby Surround DTS Digital SurroundCreating Realistic Sound Fields Available Surround modes About Relations between Speaker Layouts and Surround ModesTurning on or off the Surround modes Selecting the Surround modesPress Surround ON/OFF to Activate Surround modeIf you like to adjust sound, go to step Source you like to listen and start playingPress Test again to stop the test tone Adjust the speaker output levels -10 to +10Press Test to check if you can hear Equal levelUsing DAP Modes and All Channel Stereo PAVILION-or ALL CH Stereo appears on the display Press Surround ON/OFF to activate Surround modePress Surround Mode repeatedly Surround Mode Only for DAP modes Adjust the effect levelFollowing indications appears On the display Using DVD Multi Playback ModeActivating DVD Multi Playback Mode Press DVD MultiSynchronized Recording Compu Link Remote Control SystemPress the play 3 button on the CD player Automatic Source SelectionCase AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection Connections 2 Video Cable ConnectionsOne-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlayOperating Audio Components Sound AdjustmentEx. When you press CD Operating JVC’s Audio/Video ComponentsCassette deck CD playerCD changer TurntableYou can always perform the following operations Operating JVC’s Audio/Video ComponentsOperating Video Components DVD playerOperating To change the transmittable signals for operating a TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TVTry to operate your VCR by pressing To change the transmittable signals for operating a VCROperating Other Manufacturers’ Video Equipment Manufacturers’ codes for DVD player Codes Try to operate your DVD player by pressingManufacturers’ codes for VCR Codes Problem Possible Cause Solution TroubleshootingHarmonic distortion SpecificationsPer channel, min. RMS, driven into 8 Ω Hz to 20 kHz with no more than 0.8% totalGeneral SpecificationsFM tuner IHF AM tunerAuthorized Service Centers Limited Warranty 1201NHMMDWJEIN

RX-7020VBK specifications

The JVC RX-7020VBK is a versatile and powerful audio receiver designed to provide an immersive sound experience for home theater enthusiasts and casual listeners alike. This 5.1-channel receiver supports various audio formats and delivers high-quality sound that complements any entertainment setup. One of the standout features of the RX-7020VBK is its impressive power output. With 100 watts per channel, this receiver ensures that your audio fills the room with rich and dynamic sound. It is perfect for movies, music, and gaming, allowing every detail to come to life.

In terms of connectivity, the JVC RX-7020VBK offers multiple input options, including HDMI, digital optical, coaxial, and analog inputs. This wide range of connectivity options allows users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices, making it a versatile choice for any home entertainment system. The receiver also includes AM/FM radio capabilities, giving users access to a variety of listening options.

The RX-7020VBK is equipped with Dolby Digital and DTS surround sound technologies, providing a surround sound experience that enhances movie watching and gaming. These technologies allow for precise sound placement, giving users a realistic audio experience that draws them into the action. Furthermore, the receiver includes a built-in equalizer, offering users the ability to customize their audio settings according to their preferences.

Another noteworthy feature of the JVC RX-7020VBK is its user-friendly interface. The receiver comes with an intuitive remote control that allows for easy navigation through menus and settings, making it accessible for all users, regardless of their technical expertise. Additionally, the receiver has a sleek and modern design that blends seamlessly with any home décor.

The JVC RX-7020VBK also incorporates advanced protection circuits to safeguard against damage from overheating and overloads, ensuring longevity and reliability. With its combination of power, versatility, and user-friendly features, the JVC RX-7020VBK stands out as an excellent choice for those looking to elevate their audio experience at home. Its balance of performance and technological advancements makes it suitable for both dedicated audiophiles and casual users alike.
Top Page Image Contents