JVC RX-7020VBK manual Unit with the current setting Appears on the display, Speaker size

CONTROL

DOWN UP

T SETTING

Speaker size

Register the sizes of all the connected speakers.

•When you change your speakers, register the information about the speakers again.

1 Press SETTING repeatedly until ST SETTING

“FRNT SP (Front Speaker)”, “CNTR SP (Center Speaker)” or “REAR SP

(Rear Speaker)” (with the current setting)* appears on the display.

SPK 1

DIGITAL AUTO L C R

LINEAR PCM S.WFR LFE

LS S RS

CH-

*“LARGE” is the initial setting for the front speakers and “SMALL” is for the center and rear speakers. If you have already changed the setting, another size will be shown.

2 Press CONTROL UP 5/DOWN ∞ to CONTROL

DOWN UP

select the appropriate item about the speaker selected in the above step.

•Each time you press the button, the display changes as follows:

LARGE SMALL

NONE

LARGE : Select this when the speaker size is relatively large. (See “Notes” on the below.)

SMALL : Select this when the speaker size is relatively small. (See “Notes” on the below.)

NONE : Select this when you have not connected a speaker. (Not selectable for the front speakers)

3Repeat steps 1 and 2 to select the appropriate items for other speakers.

Notes:

•Keep the following comment in mind as reference when adjusting.

–If the size of the cone speaker unit built in your speaker is greater than 12 cm (4 3/4 inches), select “LARGE,” and if it is smaller than 12 cm (4 3/4 inches), select “SMALL.”

•If you have selected “NO” for the subwoofer setting, you can only select “LARGE” for the front speaker setting.

•If you have selected “SMALL” for the front speaker setting, you cannot select “LARGE” for the center and rear speaker settings.

Speaker distance

Register the unit you use, then the speaker distance from your listening point.

•If you have set the unit before, start from step 3.

•Speaker distance is not valid for the DVD MULTI playback mode.

1 Press SETTING repeatedly until		T	SETTING
“UNIT” (with the current setting)*
appears on the display.
	SPK 1
	DIGITAL AUTO L C R
	LINEAR PCM S.WFR LFE
	LS S RS
	CH-

*“METER” is the initial setting. If you have already changed the setting, “FEET” will be shown.

2 Press CONTROL UP 5/DOWN ∞ to select the unit.

•Each time you press the button, the setting alternates between “METER” and “FEET.”

METER : Speaker distance is shown in meter.

FEET : Speaker distance is shown in feet.

3 Press SETTING repeatedly until “FRNT DIS (Front distance),” “CNTR DIS (Center distance)” or “REAR DIS (Rear distance)” (with the current setting)* appears on the display.

•The display shows the current setting in the unit selected in

step 2.

*“3.0m” is the initial setting for meter and “10FT” is for feet. If you have already changed the setting, another value will be shown.

4 Press CONTROL UP 5/DOWN ∞ to CONTROL

DOWN UP

select the appropriate speaker distance.

•If you select “METER” in step 2, the value is changed from “0.3m” to “9.0m” by 0.3 m step.

•If you select “FEET” in step 2, the value is changed from “1FT” to “30FT” by 1 foot step.

Left front		Right front
speaker	Center speaker	speaker

3.0 m

(10 feet)

2.7 m

(9 feet)

2.4 m

(8 feet)

2.1 m

(7 feet)

Left rear	Right rear
speaker	speaker

Example: In this case,

set “FRNT DIS” to “3.0m” or “10FT,” set “CNTR DIS” to “2.7m” or “9FT” and, set “REAR DIS” to “2.4m” or “8FT.”

Note:

If you have selected “NONE” for the center and rear speakers setting,

you cannnot set the speaker distance for the center and rear speakers.

Basic Settings

17