JVC RX-7020VBK manual Basic Settings, Setting the Speaker Information Remote

Page 18

Basic Settings

Selecting the Video Input

Remote

Terminal

NOT

This receiver is equipped with the component video input terminals for the DVD player and DBS tuner, which give you higher picture quality. When you use the component video input terminals for the DVD player and/or DBS tuner, change the video input terminal setting.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1 Press SETTING repeatedly until

 

 

ST

SETTING

 

“VIDEO IN DVD ” or “VIDEO IN

 

 

 

 

 

 

 

 

DBS ” appears on the display.

 

 

•Select “VIDEO IN DVD” to select the video input terminal for the DVD player and “VIDEO IN DBS” for the DBS tuner.

SPK 1

DIGITAL AUTO L C R

LINEAR PCM

CH-

After 2 seconds, the display changes to show the current setting.

2 Press CONTROL UP 5/DOWN ∞

CONTROL

to select the appropriate type of

DOWN UP

 

the video input terminal.

 

•Each time you press the button, the display changes as follows:

 

COMPONENT

 

S/C

 

 

 

(Component)

(S-video/Composite)

 

 

COMPONENT : Select this when you connect the DVD

 

player or DBS tuner to the component video

 

input terminals.

S/C

: Select this when you connect the DVD player

 

or DBS tuner to the S-video or composite

 

video input terminal.

 

 

 

 

Note:

Without changing the video input terminal setting, you can see the picture through the video input terminals, but cannot use the AV COMPU LINK remote control system correctly (see page 32).

“NO” for the subwoofer, “LARGE” for the front speakers, and “SMALL” for the center and rear speakers are initial settings. To get best possible sound, change the subwoofer and speaker settings to fit your listening conditions.

Setting the Speaker Information Remote

NOT

To obtain the best possible sound or effect from Surround modes (see pages 26 to 29), register the following speakers and subwoofer information after all connections are completed.

The followings are items you can set:

•Subwoofer information—SUBWOOFER

•Speaker size—FRNT SP, CNTR SP, REAR SP

•Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS

•Crossover frequency—CROSS

•Low frequency effect attenuator—LFE ATT

•Dynamic range compression—D. COMP

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Subwoofer information

Register whether you have connected a subwoofer or not.

1 Press SETTING repeatedly until

 

 

 

ST

SETTING

 

 

“SUBWOOFER” (with the current

 

 

 

 

 

 

 

 

 

 

 

 

setting)* appears on the display.

 

 

 

 

 

 

 

 

 

SPK 1

 

 

 

 

DIGITAL AUTO L C R

 

 

 

 

LINEAR PCM S.WFR LFE

 

 

 

 

CH-

 

 

 

 

 

 

 

 

*“NO” is the initial setting. If you have already changed the setting, “YES” will be shown.

2 Press CONTROL UP 5/DOWN ∞ to CONTROL

DOWN UP

register whether you have connected a subwoofer or not.

•Each time you press the button, the subwoofer setting alternates between “YES” and “NO.”

YES : Select this when you have connected a subwoofer. You can adjust the subwoofer output level

(see page 20).

NO : Select this when you have not connected or have disconnected a subwoofer.

16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents RX-7020VBK Mises en garde, précautions et indications diverses For Canada/pour le CanadaTable of Contents Front Panel Remote ControlParts Identification See pages in the parentheses for detailsGetting Started Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Replace the coverAM antenna connection Connecting the FM and AM AntennasGetting Started FM antenna connectionConnecting the front speakers Connecting the SpeakersSpeaker layout diagram Connection diagramConnecting the subwoofer speaker Connecting Audio/Video ComponentsConnecting the rear and center speakers Analog connections Audio component connectionsCassette deck or CD recorder Video component connectionsCD player VCRDVD player When you connect the DVD player with stereo output jacksTV and/or DBS tuner DVD player DBS tuner BDigital connections Connecting the Power CordPlug the power cord into an AC outlet Digital output terminalBasic Operations Turning On the PowerTo turn off the power into standby mode Selecting the Source to PlayAdjusting the Volume Basic Operations Listening Only with HeadphonesTurning Off the Power With the Sleep Timer Changing the Display BrightnessSignal indicators Speaker indicators Basic adjustment auto memorySignal and speaker indicators on the display Speaker indicators light up whenBasic Settings Setting the Digital InputDigital in Terminals Selecting the Analog or Digital Input Mode Basic Settings Setting the Speaker Information RemoteSelect the appropriate speaker distance Unit with the current setting Appears on the displayPress Control UP 5/DOWN ∞ to select the unit Speaker sizeTo select the appropriate compression Press Setting repeatedly until LFE T SettingSelect the low frequency effect attenuator level LevelSound Adjustments Adjusting the Front SpeakersOutput Balance Adjusting the Subwoofer Output Level Sound AdjustmentsAdjusting the Tone Reinforcing the BassPress FM/AM Preset 5/∞ to Tuning in Stations ManuallyUsing Preset Tuning Tuner OperationsSelecting the FM Reception Mode Tuner OperationsDTS Digital Surround Creating Realistic Sound FieldsDolby Surround Typical Multichannel 5.1 ch reproductionCreating Realistic Sound Fields Selecting the Surround modes About Relations between Speaker Layouts and Surround ModesTurning on or off the Surround modes Available Surround modesSource you like to listen and start playing Activate Surround modeIf you like to adjust sound, go to step Press Surround ON/OFF toEqual level Adjust the speaker output levels -10 to +10Press Test to check if you can hear Press Test again to stop the test toneUsing DAP Modes and All Channel Stereo Only for DAP modes Adjust the effect level Press Surround ON/OFF to activate Surround modePress Surround Mode repeatedly Surround Mode PAVILION-or ALL CH Stereo appears on the displayPress DVD Multi Using DVD Multi Playback ModeActivating DVD Multi Playback Mode Following indications appears On the displayAutomatic Source Selection Compu Link Remote Control SystemPress the play 3 button on the CD player Synchronized RecordingConnections 2 Video Cable Connections AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection CaseOne-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch DVD PlayOperating JVC’s Audio/Video Components Sound AdjustmentEx. When you press CD Operating Audio ComponentsTurntable CD playerCD changer Cassette deckDVD player Operating JVC’s Audio/Video ComponentsOperating Video Components You can always perform the following operationsTry to operate your TV by pressing TV To change the transmittable signals for operating a TVOperating Other Manufacturers’ Video Equipment OperatingTo change the transmittable signals for operating a VCR Operating Other Manufacturers’ Video EquipmentTry to operate your VCR by pressing Try to operate your DVD player by pressing Manufacturers’ codes for VCR CodesManufacturers’ codes for DVD player Codes Troubleshooting Problem Possible Cause SolutionHz to 20 kHz with no more than 0.8% total SpecificationsPer channel, min. RMS, driven into 8 Ω Harmonic distortionAM tuner SpecificationsFM tuner IHF GeneralAuthorized Service Centers Limited Warranty 1201NHMMDWJEIN

RX-7020VBK specifications

The JVC RX-7020VBK is a versatile and powerful audio receiver designed to provide an immersive sound experience for home theater enthusiasts and casual listeners alike. This 5.1-channel receiver supports various audio formats and delivers high-quality sound that complements any entertainment setup. One of the standout features of the RX-7020VBK is its impressive power output. With 100 watts per channel, this receiver ensures that your audio fills the room with rich and dynamic sound. It is perfect for movies, music, and gaming, allowing every detail to come to life.

In terms of connectivity, the JVC RX-7020VBK offers multiple input options, including HDMI, digital optical, coaxial, and analog inputs. This wide range of connectivity options allows users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices, making it a versatile choice for any home entertainment system. The receiver also includes AM/FM radio capabilities, giving users access to a variety of listening options.

The RX-7020VBK is equipped with Dolby Digital and DTS surround sound technologies, providing a surround sound experience that enhances movie watching and gaming. These technologies allow for precise sound placement, giving users a realistic audio experience that draws them into the action. Furthermore, the receiver includes a built-in equalizer, offering users the ability to customize their audio settings according to their preferences.

Another noteworthy feature of the JVC RX-7020VBK is its user-friendly interface. The receiver comes with an intuitive remote control that allows for easy navigation through menus and settings, making it accessible for all users, regardless of their technical expertise. Additionally, the receiver has a sleek and modern design that blends seamlessly with any home décor.

The JVC RX-7020VBK also incorporates advanced protection circuits to safeguard against damage from overheating and overloads, ensuring longevity and reliability. With its combination of power, versatility, and user-friendly features, the JVC RX-7020VBK stands out as an excellent choice for those looking to elevate their audio experience at home. Its balance of performance and technological advancements makes it suitable for both dedicated audiophiles and casual users alike.
Top Page Image Contents