JVC RX-668RBK manual Searching for a Program by PTY Codes, Press PTY Search while, PTY codes

Page 18
PTY SEARCH
On the front panel
On the front panel

English

Searching for a Program by PTY Codes

One of the advantages of the RDS service is that you can locate a particular kind of program from the preset channels (see page 13) by specifying the PTY codes.

•To stop searching any time during the process, press PTY SEARCH while searching.

•When pressing the buttons on the remote control, make sure that you have selected the FM station using the remote control. If not, the RDS operation buttons do not work for RDS operation.

(Pressing FM/AM activates the remote control for RDS operation.)

PTY SEARCH

PTY –

+ PTY

To search for a program using the PTY codes

Before you start, remember...

•The PTY Search is only applicable to preset stations only.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1. Press PTY SEARCH while

PTY SEARCH

listening to an FM station.

 

“PTY SELECT” flashes on the display.

On the front panel

 

2. Press and hold cursor control @/

#on the front panel (or PTY + / – on the remote control) until the PTY code you want appears on the display, while “PTY SELECT” is flashing.

The display gives you the PTY codes described to the right.

3. Press PTY SEARCH again, while the PTY code selected in the previous step is still on the display.

While searching, “SEARCH” and the selected PTY code alternate on the display.

The receiver searches 30 preset FM stations, stops when it finds the one you have selected, and tunes in that station.

To continue searching after the first stop

Press PTY SEARCH again while the indications on the display are flashing.

If no program is found, “NOTFOUND” appears on the display.

PTY codes

 

 

 

NONE

 

 

 

 

 

 

 

ALARM

 

 

NEWS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEST

 

 

AFFAIRS

 

 

 

 

 

 

 

DOCUMENT

 

INFO (INFORMATION)

 

 

 

 

 

 

 

FOLK M (MUSIC)

 

 

SPORT

 

 

 

 

 

 

 

OLDIES

 

EDUCATE (EDUCATION)

 

 

 

 

 

 

 

 

 

 

NATIONAL (NATIONAL MUSIC) DRAMA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COUNTRY

 

 

CULTURE

 

 

 

 

 

 

 

JAZZ

 

 

SCIENCE

 

 

 

 

 

 

 

 

 

 

 

LEISURE

 

 

VARIED

 

 

 

 

 

 

 

 

 

 

 

TRAVEL

 

 

POP M (MUSIC)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PHONE IN

 

 

ROCK M (MUSIC)

 

 

 

 

 

 

 

RELIGION

 

M.O.R. M (MIDDLE OF ROAD MUSIC)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SOCIAL A (AFFAIRS)

 

LIGHT M (MUSIC)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLASSICS

CHILDREN

 

 

 

 

 

 

 

 

 

FINANCE

 

 

OTHER M (MUSIC)

WEATHER

When an emergency broadcast (ALARM signal) is sent from an FM station:

The receiver automatically tunes in the station except in the following cases:

•When you are listening to non-RDS stations (all AM — MW/LW and some FM stations).

•When the receiver is in standby mode.

While receiving an emergency broadcast, “ALARM” appears on the display.

The TEST signal is used for equipment test — whether it can receive the ALARM signal correctly.

The TEST signal makes the receiver work in the same way as the ALARM signal does. If the TEST signal is received, the receiver automatically switches to the station broadcasting the TEST signal. While receiving the test signal, “TEST” appears on the display.

15

Page 17 Page 19
Image 18
Page 17 Page 19
Contents RX-668RBK Per I’ltalia Español Italiano Table of Contents Front Panel Remote ControlParts Identification To use the Cursor control buttons w on the front panelChecking the Supplied Accessories Before InstallationConnecting the FM and AM MW/LW Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersConnecting Audio/Video Components Connecting the subwoofer speakerAudio component connections DVD player Video component connectionsTV or Monitor InputPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Replace the coverBasic Operations Turning the Power On and Off StandbyFrom the remote control On the front panelSelecting the Front Speakers Muting the SoundRecording a Source Adjusting the Tone Attenuating the Input SignalAdjusting the Front Speaker Output Balance Reinforcing the BassPress Setting so that the cursor Basic SettingsSetting Center and Rear Speakers for DSP Modes Changing the Source NameUsing the Sleep Timer Adjust the sound using the functions listed abovePress ONE Touch Operation Tuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Using the RDS Radio Data System to Receive FM Stations When an FM stereo broadcast is hard to receive or noisyWhat Information Can RDS Signals Provide? Press PTY Search while To search for a program using the PTY codesSearching for a Program by PTY Codes Listening to an FM stationSwitching to a Broadcast Program of Your Choice Temporarily Press TA/NEWS/INFO untilProgram type you want appears on Display Surround Modes Using the DSP Modes3D-PHONIC modes Dolby SurroundRear Available DSP Modes According to the Speaker ArrangementFront Rear SpeakerAdjusting the 3D-PHONIC Modes Adjusting DAP ModesOutput balance Press Rearl / + to adjust the rear speaker output levelUntil the mode PRO Logic Or Theater appears on Display Rear speaker output level from 10 to +10Activating the DSP Modes Press Surround repeatedly Until the DSP mode you wantTo cancel the DSP mode Select and play a sound sourceUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModeUsing the On-Screen Menus Bass Boost function To Bass BoostPress @/ #to turn On or OFFPress % / Þto move to Surround LEVEL, then press @/ # Press %/ Þ/ @/ #to adjust the tone as you wantPress %/ Þto move to SETTING, then press @/ # Press %/ Þto move to Tone CONTROL, then press @/ #Press %/ Þto move To Tuner CONTROL, then Press @/ # Press %/ Þto move to Preset MEMORY, then press @/ #Storing the Preset Stations Also see Press %/ Þto move to RDS INFORMATION, then press @/ #Same time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemCD player MD recorder Disc Search Only for CD PlayerTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Press on Screen Exit againPress %/ Þto move to PERFORMER, then press on Press Text Display while CD is selected as the sourcePress %/ Þto move to SEARCH, then Press on Screen SET Press on Screen SET againThen press on Screen SET Press %/ Þto move To Search Then press onPress %/ Þto move To GENRE, then Press on Screen Entering the Disc InformationPress Text Display while MD is selected as the source Up to 32 characters to this User FileEnter the disc title, referring to steps 3 For the MD recorderSound control section Amplifier Operating JVC’s Audio/Video ComponentsTuner CD playerCassette deck MD recorderDVD player Troubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM MW/LW tunerEN, GE, FR, NL, SP, IT 0299JTMMDWJEM

RX-668RBK specifications

The JVC RX-668RBK is a commendable addition to the world of home audio receivers, delivering a blend of impressive features and robust sound performance ideal for both casual listeners and audiophiles alike. This 5.1-channel AV receiver stands as a testament to JVC's commitment to quality and innovation in home entertainment systems.

One of the standout features of the RX-668RBK is its power output. Capable of delivering up to 100 watts per channel, the receiver ensures that users can enjoy clear, dynamic sound at any volume level. The receiver supports a range of audio formats, including Dolby Digital and DTS, which provide an immersive experience during movie nights or while enjoying music. This multi-channel setup allows for true surround sound, transporting listeners straight into the action.

The RX-668RBK is equipped with a sophisticated digital signal processing technology that enhances audio quality across different types of content. The built-in equalizer function offers users the flexibility to customize their sound preferences, allowing for adjustments based on the specifics of the room and the type of media being played. Whether you are watching a fast-paced action film or listening to your favorite album, the receiver adapts seamlessly to deliver optimal sound performance.

Connectivity options are plentiful, as the RX-668RBK features multiple HDMI inputs, enabling users to connect a variety of sources, such as Blu-ray players, gaming consoles, and streaming devices. The receiver also includes optical and coaxial digital inputs, as well as analog audio inputs, ensuring compatibility with both modern and legacy devices. Additionally, the front USB input allows for easy connectivity to USB sources, making it simple to play digital music files.

The user interface of the JVC RX-668RBK is designed for convenience, featuring an intuitive on-screen display that simplifies setup and navigation. The remote control enhances this ease of use, allowing users to manage their audio settings and select input sources from the comfort of their couch.

Overall, the JVC RX-668RBK stands out for its robust feature set, superior sound processing technologies, and versatile connectivity options. It is a reliable choice for anyone looking to enhance their home audio experience, creating a perfect blend of convenience, quality, and exceptional performance.
Top Page Image Contents