Horizon Fitness AT1501 manual Attach the Crank CAP to the Crank Repeat on opposite side

Page 8

INTRODUCTION IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE ASCENT TRAINER CONDITIONING TROUBLESHOOTING LIMITED

YOU BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY

14

ASSEMBLY STEP 8

HARDWARE BAG 8 CONTENTS:

 

 

 

BOLT (C)

WASHER (D)

WAVY WASHER (J)

AXLE

16 mm

25 mm

29 mm

Qty: 2

Qty: 6

Qty: 6

Qty: 2

 

ASSEMBLY STEP 8:

TOP HANDRAIL

CRANK

 

BOLT (C)

WASHER (D)

WAVY WASHER (J)

CRANK CAP

 

BOLT (C)

WASHER (D)

SWING CAP

AXLE

BOLT (C)

SWING CAP

WASHER (D)

RIGHT SWING ARM

PEDAL ARM

LINK ARM

PACKAGING PLASTIC

ALay waste packaging plastic over the BASE RAIL. This will prevent the PEDAL ARM assembly from scratching the ascent trainer’s paint.

BOpen HARDWARE BAG 8.

CPlace 1 WAVY WASHER (J) onto CRANK.

DAttach the right PEDAL ARM of the assembly to the right CRANK using 1 WASHER (D) and 1 BOLT (C).

EAttach right SWING ARM to TOP HANDRAIL using 2 SWING CAPS, 2 BOLTS (C), 1 SHAFT and 2 WASHERS (D).

FAttach the CRANK CAP to the CRANK

GRepeat on opposite side.

ASSEMBLY STEP 9

HARDWARE BAG 9 CONTENTS:

 

 

 

 

BOLT (N)

WASHER (L)

ROD BEARING

SPACER

NUT (G)

45 mm

18 mm

SHAFT

Qty: 4

8 mm

Qty: 2

Qty: 2

Qty: 2

 

Qty: 2

ASSEMBLY STEP 9:

LOWER

HANDLEBAR

WASHER (L)

NUT (G)

BOLT (N)

SPACER

 

ROD BEARING

SPACER

SHAFT

 

LINK ARM

AOpen HARDWARE BAG 9.

BSlide 1 ROD BEARING SHAFT into the joint end of right LINK ARM.

CFit 1 SPACER on each side of each ROD BEARING SHAFT after the ROD BEARING SHAFTS are in LINK ARM.

DAttach right LINK ARM to the right LOWER HANDLEBAR using 1 BOLT (N), 1 WASHER (L) and 1 NUT (G).

ERepeat on opposite side.

15

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

LIMITED TROUBLESHOOTING CONDITIONING ASCENT TRAINER BEFORE WARRANTY & MAINTENANCE GUIDELINES OPERATION YOU BEGIN

AT1501_Rev.2.6.indd 14-15

7/31/08 12:43:49 PM

Image 8
Contents Ascent Trainer USER’S Guide Table of Contents T R O D U C T I O NImportant Precautions S E M B LYUnpacking Enter Your Serial Number Model Name in the Boxes belowParts Included Diagram and Parts ListTools Included Open Hardware BAG Conditioning Guidelines Repeat with the left Link ARM Attach the Crank CAP to the Crank Repeat on opposite side Adjusting Levelers Before YOU BeginYOU’RE Finished Location of the Ascent TrainerPower Ascent Trainer OperationMoving AT1501 ConsoleProgram Profiles Workout ProfilesSelecting Programs Heart Rate HandlebarsPerceived Exertion Level Using SPEAKER/MP3 Audio FunctionConditioning Guidelines Target Heart Rate Zone Chart StretchingWarm UP Cool DownAchieving Your Fitness Goals Keeping AN Exercise DiaryTroubleshooting Monthly LOG SheetWeek # Calories TimeHeart Rate Troubleshooting When YOU are Near the EquipmentCommon Product Questions HOW Long will the Drive Belt LAST?I N T E N a N C E Limited Home USE Warranty Customer Tech Support