JVC RX-664VBK Audio component connections, Video component connections, TV and VCR connection

Page 14

Getting Started

Connecting Audio/Video Components

You can connect the following components to the receiver using cables with RCA pin plugs.

Audio Components		Video Components
•	Turntable	•	TV
•	CD player	•	VCR

•	Cassette deck	•	DVD player

Audio component connections

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.

If a ground cable is provided for your turntable, connect the cable to the GND terminal of the AM LOOP terminals on the rear panel.

To audio output

Note:

Any turntables incorporating a

ANTENNA

FM 75

FM

GND

GND

AM

LOOP

AM

EXT

DVD

FRONT CENTER REAR

L

R

SUBWOOFER

PHONO CD AUDIO

L

R

OUT

(REC)

DVD

			MONITOR
LEFT			OUT
RIGHT		OUT	IN
RIGHT		(REC)	(PLAY)
		(REC)	(PLAY)
		VCR
TAPE	TV	OUT	IN
TAPE	SOUND	(REC)	(PLAY)
	SOUND		LEFT
			LEFT

RIGHT

IN

(PLAY)

CD player

small-output cartridge such as an MC (moving-coil type) must be connected to the receiver through a commercial head amplifier or step-up transformer. Direct connection may result in unsufficient volume.

	Turntable	To audio
	Turntable	output
		output

To audio output

To audio input Cassette deck

If your audio components have a COMPU LINK-3 terminal

The COMPU LINK remote control system allows you to control other JVC audio components from the receiver or vice versa.

For detailed information about the COMPU LINK-3 remote control system, see page 40.

Video component connections

TV and VCR connection

To video input (see note to the right)

			DVD
		FRONT	CENTER	REAR
		L
		R
		SUBWOOFER
	To audio output	PHONO	CD	AUDIO
	To audio output
TV		L
TV
		R
				OUT
				(REC)

	DVD	VIDEO
			MONITOR
LEFT			OUT
RIGHT		OUT	IN
RIGHT		(REC)	(PLAY)
		(REC)	(PLAY)
		VCR
TAPE	TV	OUT	IN
TAPE	SOUND	(REC)	(PLAY)
	SOUND		LEFT
			LEFT

RIGHT

IN

(PLAY)

Note:

When connecting a JVC TV:

• If you use the AV COMPU LINK

remote control system to

operate the TV, connect the

receiver to the Video Input 2

jack on the TV.

• If you do not use the AV

COMPU LINK remote control

system to operate the TV,

connect the receiver to the

	To audio/video input
VHS
VCR	To audio/video output
VCR

Video Input 1 jack on the TV.

11

Image 14

Contents RX-664VBK To Reduce the Risk of Electric Shock For actual setting procedures, see pages 26 to Center Speaker Level Rear Speaker Level Effect LevelTable of Contents Front Panel Remote ControlParts Identification Easy Set Up & Operations For Reproducing Surround Sound with your VCRTurn on the power Easy Set Up & Operations For Reproducing DVD Multi Playback with your DVD playerAudio Sound VCR Control Disc Locations Getting StartedGeneral Handling the receiverAM Antenna Connections Connecting the FM and AM AntennasFM Antenna Connections Getting Started Connecting the front speakersConnecting the Speakers Connect the front speakers to the Front Speakers terminalsConnecting the rear and center speakers Connecting the subwooferVideo component connections Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalDVD player connection If your audio components have an AV Compu Link terminalConnecting the Power Cord Putting Batteries in the Remote ControlBasic Operations From the remote controlTurning the Power On and Off On the front panelOn the front panel only From the remote control onlyBasic Operations Recording a Source Listening with HeadphonesTo listen with only headphones Listening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep TimerReceiver turns off automatically When the shut-off time comesTo cancel the Sleep Timer Press Sleep repeatedlySmall Basic SettingsSelecting the Center Speaker Size LargeTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Selecting the FM Reception Mode Receiving Radio BroadcastsTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Using the Preset SEA Modes Press SEA Preset to select the effect levelOn the DAP mode Using the Surround ProcessorOn JVC 3D-PHONIC mode On surround modes3DACTION Using the Surround ProcessorUsing JVC 3D-PHONIC Modes 3DTHEATRPress Effect to select the effect level Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Each time you press the button, the level changes asHall Using the DAP ModesPavilion Press Rear L +/- to adjust the rear speaker Output level To cancel the DAP modeSelect OFF in step DAP indicator goes off from the display Effect Speaker Arrangements for Surround Modes Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode This casePrologic Preparing for Surround ModesPress Surround so that the Control %/ Þ/ @ / # TheaterWide Press Control @/ # to select the center modeDelay NormalIf necessary, adjust the speaker output balance as follows Each time you press the button, the effect level changesPress Test again to stop the test tone Press Effect to adjust the effect levelPress Test to start checking the speaker output balance Previous mode is recalled with its previous Using Surround ModesTo cancel Surround mode From the front panelActivating the DVD Multi playback Using the DVD Multi Playback ModeSpeaker arrangements for DVD Multi playback Using the DVD Multi Playback Mode Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingAV Compu Link Remote Control System Components with RCA pin plugsSee page 44 for details Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlayStarts playing To operate JVC audio components using this remote controlOperating Other Components Starts playbackFollowing operations on the TV To operate JVC video components using this remote controlAfter pressing TV SOUND, you can perform Return TV Volume +TV/VIDEO Equipment requires pressing Enter Section Converter or satellite tunerSelects the channel Alternates between previouslyOperating Other Manufacturers’ Video Equipment Release VCR in the Power sectionTry to operate your VCR by pressing VCR Power Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierGeneral FM tuner IHFAM tuner HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM