JVC RX-664VBK manual Receiving Radio Broadcasts, Tuning in Stations Manually, Using Preset Tuning

Page 24

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.

Tuning in Stations Manually

On the front panel only:

TUNER/BAND

1. Press TUNER/BAND.

The lamp above the button lights up.

Each time you press the button, the band alternates between FM and AM.

2. Press Control % / Þuntil “–TUNING+” appears on the display.

3. Press Control @/ # until you find the frequency you want.

• Pressing Control @ decreases the frequency.

• Pressing Control # increases the frequency.

Using Preset Tuning

Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 40 stations at random.

To store the preset stations

On the front panel only:

1.Tune in the station you want to preset (see above). If you want to store the FM reception mode for this station, select the FM reception mode you want. See page 23 for details.

2. Press MEMORY.

MEMORY

The channel number starts flashing on the display for about 5 seconds.

3. Press Control @ / #to select a channel number while the channel number position is flashing.

• Pressing Control @decreases the number.

• Pressing Control #increases the number.

4. Press MEMORY again while the selected channel

Notes:

When you hold down Control @ / # in step 3, the frequency keeps changing until you press Control @/ #again or a station is tuned in.

When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display.

When an FM stereo program is received, the STEREO indicator also lights up.

CAUTION:

Preset stations may be erased in a few days when power is cut off to the receiver, as when it is unplugged from the AC outlet or a power failure occurs. If the preset stations are lost, simply set the stations again.

Note:

You can press 10 keys on the remote control to select a channel number in step 3, if you have

number is flashing on the display.

MEMORY

pressed TUNER/BAND on the

The selected channel number stops flashing.

The station is assigned to the selected channel number.

remote control prior to starting this preset procedures.

For channel number 5, press 5.

For channel number 15, press +10 then 5.

For channel number 20, press +10 then 10.

For channel number 30, press +10, +10, then 10.

21

Image 24
Contents RX-664VBK To Reduce the Risk of Electric Shock For actual setting procedures, see pages 26 to Center Speaker Level Rear Speaker Level Effect LevelTable of Contents Remote Control Parts IdentificationFront Panel Easy Set Up & Operations For Reproducing Surround Sound with your VCRTurn on the power Easy Set Up & Operations For Reproducing DVD Multi Playback with your DVD playerAudio Sound VCR Control Disc Getting Started GeneralLocations Handling the receiverConnecting the FM and AM Antennas FM Antenna ConnectionsAM Antenna Connections Connecting the front speakers Connecting the SpeakersGetting Started Connect the front speakers to the Front Speakers terminalsConnecting the rear and center speakers Connecting the subwooferConnecting Audio/Video Components Audio component connectionsVideo component connections If your audio components have a Compu LINK-3 terminalDVD player connection If your audio components have an AV Compu Link terminalConnecting the Power Cord Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and OffBasic Operations On the front panelFrom the remote control only Basic OperationsOn the front panel only Listening with Headphones To listen with only headphonesRecording a Source Basic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes To cancel the Sleep TimerReceiver turns off automatically Press Sleep repeatedlyBasic Settings Selecting the Center Speaker SizeSmall LargeTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo cancel a stored preset station To tune in a preset stationPress 10 keys to select a preset channel number Selecting the FM Reception Mode Receiving Radio BroadcastsUsing the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelUsing the Surround Processor On JVC 3D-PHONIC modeOn the DAP mode On surround modesUsing the Surround Processor Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRPress Control @ / #to adjust the effect level To cancel the 3D-PHONIC modePress Effect to select the effect level Each time you press the button, the level changes asUsing the DAP Modes PavilionHall To cancel the DAP mode Select OFF in step DAP indicator goes off from the displayPress Rear L +/- to adjust the rear speaker Output level Effect Select Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This casePreparing for Surround Modes Press Surround so that the Control %/ Þ/ @ / #Prologic TheaterPress Control @/ # to select the center mode DelayWide NormalIf necessary, adjust the speaker output balance as follows Each time you press the button, the effect level changesPress Effect to adjust the effect level Press Test to start checking the speaker output balancePress Test again to stop the test tone Using Surround Modes To cancel Surround modePrevious mode is recalled with its previous From the front panelUsing the DVD Multi Playback Mode Speaker arrangements for DVD Multi playbackActivating the DVD Multi playback Using the DVD Multi Playback Mode Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingAV Compu Link Remote Control System Components with RCA pin plugsAutomatic Selection of TV’s Input Mode Automatic Power On/OffSee page 44 for details One-Touch Video PlayTo operate JVC audio components using this remote control Operating Other ComponentsStarts playing Starts playbackTo operate JVC video components using this remote control After pressing TV SOUND, you can performFollowing operations on the TV TV Volume + TV/VIDEOReturn Section Converter or satellite tuner Selects the channelEquipment requires pressing Enter Alternates between previouslyRelease VCR in the Power section Try to operate your VCR by pressing VCR PowerOperating Other Manufacturers’ Video Equipment Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF AM tunerGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM