JVC RX-664VBK manual Compu Link Remote Control System, Automatic Source Selection

Page 43

COMPU LINK Remote Control System

The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver.

To use this remote control system, you need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks with the cable (monaural mini-plug supplied with those components):

COMPU LINK – 3

(SYNCHRO)

CD player

Cassette deck

 

Turntable

This remote control system allows you to use the four functions listed below.

Remote Control through the Remote Sensor on the Receiver

You can control JVC audio components through the remote sensor on the receiver using this remote control. Aim the remote control directly at the remote sensor on the receiver. For details, see page 43.

Automatic Source Selection

When you press the play (3) button on a connected component or on its own remote control, the receiver automatically turns on and changes the source to the component. On the other hand, if you select a new source on the receiver or the remote control, the selected component begins playing immediately.

In both cases, the previously selected source continues playing without sound for a few seconds.

Automatic Power On/Off (only possible with the COMPU LINK-3 connection)

Both the CD player and cassette deck turn on and off with the receiver. When you turn on the receiver, the CD player or cassette deck will turn on automatically, depending on which component has been previously selected. When you turn off the receiver, both the CD player and cassette deck will turn off.

Synchronized Recording

Synchronized recording means the cassette deck starts recording as soon as a CD (or a record) begins playing.

To use synchronized recording, follow these steps:

1Put a tape in the cassette deck, and a disc in the CD player (or a record on the turntable).

2Press the record (¦) button and the pause (8) button on the cassette deck at the same time.

This puts the cassette deck into recording pause.

If you do not press the record (¦) button and pause (8) button at the same time, the synchronized recording will not start.

3Press the play (3) button on the CD player (or on the turntable).

The source changes on the receiver, and as soon as play starts, the cassette deck starts recording. When the play ends, the cassette deck enters recording pause, and stops about 4 seconds later.

Notes:

Without connecting the audio components with RCA pin plugs as described on page 11, the COMPU LINK remote control system cannot operate the components.

Refer also to the manuals supplied with your audio components.

Notes:

During synchronized recording, the selected source cannot be changed.

If your CD player is playing in program mode, a 4-second blank is recorded between tracks so that the music scan feature of your cassette deck can be used on the recorded tape.

If the power of any component is shut off during synchronized recording, the COMPU LINK remote control system may not operate properly. In this case, you must start again from the beginning.

40

Image 43
Contents RX-664VBK To Reduce the Risk of Electric Shock Center Speaker Level Rear Speaker Level Effect Level For actual setting procedures, see pages 26 toTable of Contents Parts Identification Remote ControlFront Panel For Reproducing Surround Sound with your VCR Easy Set Up & OperationsTurn on the power For Reproducing DVD Multi Playback with your DVD player Easy Set Up & OperationsAudio Sound VCR Control Disc Handling the receiver Getting StartedGeneral LocationsFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connect the front speakers to the Front Speakers terminals Connecting the front speakersConnecting the Speakers Getting StartedConnecting the subwoofer Connecting the rear and center speakersIf your audio components have a Compu LINK-3 terminal Connecting Audio/Video ComponentsAudio component connections Video component connectionsIf your audio components have an AV Compu Link terminal DVD player connectionPutting Batteries in the Remote Control Connecting the Power CordOn the front panel From the remote controlTurning the Power On and Off Basic OperationsBasic Operations From the remote control onlyOn the front panel only To listen with only headphones Listening with HeadphonesRecording a Source Using the Sleep Timer Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessPress Sleep repeatedly When the shut-off time comesTo cancel the Sleep Timer Receiver turns off automaticallyLarge Basic SettingsSelecting the Center Speaker Size SmallOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Receiving Radio Broadcasts Selecting the FM Reception ModeSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn surround modes Using the Surround ProcessorOn JVC 3D-PHONIC mode On the DAP mode3DTHEATR Using the Surround ProcessorUsing JVC 3D-PHONIC Modes 3DACTIONEach time you press the button, the level changes as Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Press Effect to select the effect levelPavilion Using the DAP ModesHall Select OFF in step DAP indicator goes off from the display To cancel the DAP modePress Rear L +/- to adjust the rear speaker Output level Effect This case Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode Speaker Arrangements for Surround ModesTheater Preparing for Surround ModesPress Surround so that the Control %/ Þ/ @ / # PrologicNormal Press Control @/ # to select the center modeDelay WideEach time you press the button, the effect level changes If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output balance Press Effect to adjust the effect levelPress Test again to stop the test tone From the front panel Using Surround ModesTo cancel Surround mode Previous mode is recalled with its previousSpeaker arrangements for DVD Multi playback Using the DVD Multi Playback ModeActivating the DVD Multi playback Using the DVD Multi Playback Mode Synchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionComponents with RCA pin plugs AV Compu Link Remote Control SystemOne-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off See page 44 for detailsStarts playback To operate JVC audio components using this remote controlOperating Other Components Starts playingAfter pressing TV SOUND, you can perform To operate JVC video components using this remote controlFollowing operations on the TV TV/VIDEO TV Volume +Return Alternates between previously Section Converter or satellite tunerSelects the channel Equipment requires pressing EnterTry to operate your VCR by pressing VCR Power Release VCR in the Power sectionOperating Other Manufacturers’ Video Equipment Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsAM tuner FM tuner IHFGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM