JVC RX-664VBK manual TV Volume +, Tv/Video, Return

Page 48

Operating Other Manufacturers’ Video Equipment

This remote control supplied with the receiver can transmit control signals for other manufacturers’ VCRs, TVs, CATV converters and satellite tuners. By changing the transmittable signals from preset ones to the other manufacturers’, you can operate the other manufacturer’s components using this remote control.

When operating the other manufacturers’ components, refer also to the manuals supplied with them. To operate these components with the remote control, first you need to set the manufacturer’s code each for VCR, TV, CATV converters, and satellite tuner.

To change the transmittable signals for operating another manufacturer’s TV

1.Press and hold TV (in the POWER section).

2.Press TV SOUND.

3.Enter manufacturer’s code (two digits) using buttons 1–9, and 0.

See the list below to find the code.

4.Release TV in the POWER section.

The following buttons can be used for operating the TV:

TV	Turns on and off the TV.
(in the POWER section)
TV VOLUME +/–	Adjusts the volume.
TV/VIDEO	Sets the input mode (either TV
	or VIDEO).

		POWER
CATV/SAT		TV	VCR			AUDIO
		CATV				SOUND
	CONTROL CD-DISC CONTROL
DAP MODE		3D-PHONIC			SURROUND
1			2			3
EFFECT			DELAY			TEST
4			5			6
SEA MODE		SEA PRESET				MENU
7/P			8			9
100+	– REAR•R +				RETURN/ENTER
+10			0			10
CENTER		REAR	TV			CH
		(L)	VOLUME
SLEEP	ONE TOUCH TV/VIDEO
	OPERATION
			CD		TAPE
TUNER/					TAPE
BAND
TV			VCR		DVD
TV
SOUND		MUTING
SOUND				DVD
						MULTI
PHONO
PHONO

VOLUME

Note:

Refer to the manual supplied with your TV.

After pressing TV SOUND, you can perform the following operations on the TV:

CH +/–	Changes the channels.
1 – 9, 0, 100+ (+10)	Selects the TV channels.
	100+ (+10) button will function as
	the ENTER button if your
	TV requires pressing ENTER
	after selecting a channel number.
RETURN	Alternates between the previously
	selected channel and the current channel.

5.Try to operate your TV by pressing TV in the POWER section. When your TV turns on or off, you have entered the correct code.

RM-SR664U

REMOTE CONTROL

If there are more than one code listed for your brand of TV, try each one until

the correct one is entered.

	Manufacturer	Code	Manufacturer	Code
	HITACHI	10	SAMSUNG	12
	JVC	01	SANYO	13
	MAGNAVOX	02	SHARP	06		Manufacturers’ codes are
	MAGNAVOX	02	SHARP	06		subject to change without

	MITSUBISHI	03	SONY	07
	MITSUBISHI	03	SONY	07		notice. If they are changed,

	PANASONIC	04, 11	TOSHIBA	08
	PANASONIC	04, 11	TOSHIBA	08		this remote control cannot
	RCA	05	ZENITH	09		operate the equipment.

45

Image 48

Contents RX-664VBK To Reduce the Risk of Electric Shock For actual setting procedures, see pages 26 to Center Speaker Level Rear Speaker Level Effect LevelTable of Contents Remote Control Parts IdentificationFront Panel Easy Set Up & Operations For Reproducing Surround Sound with your VCRTurn on the power Easy Set Up & Operations For Reproducing DVD Multi Playback with your DVD playerAudio Sound VCR Control Disc Getting Started GeneralLocations Handling the receiverConnecting the FM and AM Antennas FM Antenna ConnectionsAM Antenna Connections Connecting the front speakers Connecting the SpeakersGetting Started Connect the front speakers to the Front Speakers terminalsConnecting the rear and center speakers Connecting the subwooferConnecting Audio/Video Components Audio component connectionsVideo component connections If your audio components have a Compu LINK-3 terminalDVD player connection If your audio components have an AV Compu Link terminalConnecting the Power Cord Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and OffBasic Operations On the front panelFrom the remote control only Basic OperationsOn the front panel only Listening with Headphones To listen with only headphonesRecording a Source Basic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes To cancel the Sleep TimerReceiver turns off automatically Press Sleep repeatedlyBasic Settings Selecting the Center Speaker SizeSmall LargeTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo cancel a stored preset station To tune in a preset stationPress 10 keys to select a preset channel number Selecting the FM Reception Mode Receiving Radio BroadcastsUsing the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelUsing the Surround Processor On JVC 3D-PHONIC modeOn the DAP mode On surround modesUsing the Surround Processor Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRPress Control @ / #to adjust the effect level To cancel the 3D-PHONIC modePress Effect to select the effect level Each time you press the button, the level changes asUsing the DAP Modes PavilionHall To cancel the DAP mode Select OFF in step DAP indicator goes off from the displayPress Rear L +/- to adjust the rear speaker Output level Effect Select Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This casePreparing for Surround Modes Press Surround so that the Control %/ Þ/ @ / #Prologic TheaterPress Control @/ # to select the center mode DelayWide NormalIf necessary, adjust the speaker output balance as follows Each time you press the button, the effect level changesPress Effect to adjust the effect level Press Test to start checking the speaker output balancePress Test again to stop the test tone Using Surround Modes To cancel Surround modePrevious mode is recalled with its previous From the front panelUsing the DVD Multi Playback Mode Speaker arrangements for DVD Multi playbackActivating the DVD Multi playback Using the DVD Multi Playback Mode Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingAV Compu Link Remote Control System Components with RCA pin plugsAutomatic Selection of TV’s Input Mode Automatic Power On/OffSee page 44 for details One-Touch Video PlayTo operate JVC audio components using this remote control Operating Other ComponentsStarts playing Starts playbackTo operate JVC video components using this remote control After pressing TV SOUND, you can performFollowing operations on the TV TV Volume + TV/VIDEOReturn Section Converter or satellite tuner Selects the channelEquipment requires pressing Enter Alternates between previouslyRelease VCR in the Power section Try to operate your VCR by pressing VCR PowerOperating Other Manufacturers’ Video Equipment Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF AM tunerGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM