JVC RX-664VBK manual Press Control @/ # to select the center mode, Wide, Normal, Phantom, Delay

Page 37

5. Press Control @/ # to select the center mode.

Each time you press the button, the center modes change

as follows:

 

 

 

 

 

 

 

WIDE

 

 

NORMAL

 

PHANTOM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WIDE

Select this mode when the center speaker can reproduce the bass

 

 

 

better than the front speakers. All signals of the center channel are

 

 

 

output through the center speaker.

 

 

 

 

 

 

 

 

NORMAL

Select this mode when the center speaker cannot reproduce the

 

 

 

bass better than the front speakers. The bass portions of the center

 

 

 

channel signals are output through the front speakers.

 

 

 

 

 

 

 

 

PHANTOM

Select this mode when you do not use a center speaker. The center

 

 

 

speaker channel signals are output through the front speakers.

 

 

 

 

 

 

 

 

 

6. Press Control %/ Þ until “–DELAY +” appears on the display.

7. Press Control @/ #to adjust the delay time of the rear speaker output.

Each time you press the button, the delay time changes as follows:

DELAY 1 DELAY 2 DELAY 3

DELAY 1

Select this when the distance from you to your rear speakers is

 

greater than that to the front speakers.

 

 

DELAY 2

Select this when the distance from you to your rear speakers is

 

almost equal to that to the front speakers.

 

 

DELAY 3

Select this when the distance from you to your rear speakers is less

 

than that to the front speakers.

 

 

8. Press Control %/ Þ until “TEST” appears on the display, then press Control @/ # to start checking the speaker output balance.

“TEST” starts flashing on the display, and a test tone comes out of the speakers in the following order:

Left front

 

Center

 

Right front

speaker

 

speaker

 

speaker

Rear speakers

Continued to the next page.

Notes:

If you have already set the center speaker size following the procedure described on page 19, you do not have to select the center mode in this procedure.

When you have selected “3CHLOGIC,” you cannot select “PHANTOM.”

Note:

When you have selected “3CHLOGIC” or “THEATER,” you cannot adjust the delay time.

Notes:

No test tone comes out of the rear speakers when you have selected “3CHLOGIC.”

No test tone comes out of the center speaker when you select “PHANTOM” for the center mode.

34

Image 37
Contents RX-664VBK To Reduce the Risk of Electric Shock Center Speaker Level Rear Speaker Level Effect Level For actual setting procedures, see pages 26 toTable of Contents Parts Identification Remote ControlFront Panel For Reproducing Surround Sound with your VCR Easy Set Up & OperationsTurn on the power For Reproducing DVD Multi Playback with your DVD player Easy Set Up & OperationsAudio Sound VCR Control Disc General Getting StartedLocations Handling the receiverFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connecting the Speakers Connecting the front speakersGetting Started Connect the front speakers to the Front Speakers terminalsConnecting the subwoofer Connecting the rear and center speakersAudio component connections Connecting Audio/Video ComponentsVideo component connections If your audio components have a Compu LINK-3 terminalIf your audio components have an AV Compu Link terminal DVD player connectionPutting Batteries in the Remote Control Connecting the Power CordTurning the Power On and Off From the remote controlBasic Operations On the front panelBasic Operations From the remote control onlyOn the front panel only To listen with only headphones Listening with HeadphonesRecording a Source Adjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Using the Sleep TimerTo cancel the Sleep Timer When the shut-off time comesReceiver turns off automatically Press Sleep repeatedlySelecting the Center Speaker Size Basic SettingsSmall LargeTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Receiving Radio Broadcasts Selecting the FM Reception ModeSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn JVC 3D-PHONIC mode Using the Surround ProcessorOn the DAP mode On surround modesUsing JVC 3D-PHONIC Modes Using the Surround Processor3DACTION 3DTHEATRTo cancel the 3D-PHONIC mode Press Control @ / #to adjust the effect levelPress Effect to select the effect level Each time you press the button, the level changes asPavilion Using the DAP ModesHall Select OFF in step DAP indicator goes off from the display To cancel the DAP modePress Rear L +/- to adjust the rear speaker Output level Effect Select 3CHLOGIC Select Normal or Wide for center mode Select Prologic or Theater Select Phantom for center modeSpeaker Arrangements for Surround Modes This casePress Surround so that the Control %/ Þ/ @ / # Preparing for Surround ModesPrologic TheaterDelay Press Control @/ # to select the center modeWide NormalEach time you press the button, the effect level changes If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output balance Press Effect to adjust the effect levelPress Test again to stop the test tone To cancel Surround mode Using Surround ModesPrevious mode is recalled with its previous From the front panelSpeaker arrangements for DVD Multi playback Using the DVD Multi Playback ModeActivating the DVD Multi playback Using the DVD Multi Playback Mode Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingComponents with RCA pin plugs AV Compu Link Remote Control SystemAutomatic Power On/Off Automatic Selection of TV’s Input ModeSee page 44 for details One-Touch Video PlayOperating Other Components To operate JVC audio components using this remote controlStarts playing Starts playbackAfter pressing TV SOUND, you can perform To operate JVC video components using this remote controlFollowing operations on the TV TV/VIDEO TV Volume +Return Selects the channel Section Converter or satellite tunerEquipment requires pressing Enter Alternates between previouslyTry to operate your VCR by pressing VCR Power Release VCR in the Power sectionOperating Other Manufacturers’ Video Equipment Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsAM tuner FM tuner IHFGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM