JVC RX-664VBK manual Specifications, Amplifier

Page 52

Specifications

Output Power At Stereo operation 100 watts per channel, min. RMS, driven into 8 ohms, 40 Hz to 20 kHz with no more than 0.8 % total harmonic distortion.

Amplifier

Output Power

At Surround operation

 

 

Front channels

100 watts per channel, min. RMS,

 

 

driven into 8 ohms at 1 kHz, with no

 

 

more than 0.8% total harmonic

 

 

distortion.

 

Center channel

100 watts, min. RMS, driven into 8

 

 

ohms at 1 kHz, with no more than 0.8

 

 

% total harmonic distortion.

 

Rear channels

100 watts per channel, min. RMS,

 

 

driven into 8 ohms at 1kHz, with no

 

 

more than 0.8 % total harmonic

 

 

distortion.

Total Harmonic Distortion (8 ohms, 1 kHz)

0.8 %* at 100 watts output

 

 

(* Measured by JVC Audio Analysis

 

 

System)

Frequency Response (8 ohms)

PHONO (MM)

20 Hz to 20 kHz (±1 dB)

 

CD, TAPE, TV SOUND, VCR, DVD

20 Hz to 20 kHz (±1 dB)

Audio Input Sensitivity/Impedance (1 kHz)

PHONO

2.7 mV/47 k ohms

 

CD, TAPE, TV SOUND, VCR, DVD

220 mV/47 k ohms

Audio Output Level

TAPE, VCR

220 mV

Signal-to-Noise Ratio (’66 IHF/’78 IHF)

PHONO

70 dB/78 dB

 

CD, TAPE, TV SOUND, VCR, DVD

87 dB/80 dB

Loudness control (Volume Control at –40 dB)

+5 ±2 dB at 100 Hz

Video Input Sensitivity/Impedance

VCR, DVD

1 Vp-p/75 ohms

Video Output Level

VCR, MONITOR OUT

1 Vp-p (at 1 Vp-p input),

 

 

sync negative

Signal-to-Noise Ratio

45 dB

49

Image 52
Contents RX-664VBK To Reduce the Risk of Electric Shock For actual setting procedures, see pages 26 to Center Speaker Level Rear Speaker Level Effect LevelTable of Contents Parts Identification Remote ControlFront Panel Easy Set Up & Operations For Reproducing Surround Sound with your VCRTurn on the power Easy Set Up & Operations For Reproducing DVD Multi Playback with your DVD playerAudio Sound VCR Control Disc Getting Started GeneralLocations Handling the receiverFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connecting the front speakers Connecting the SpeakersGetting Started Connect the front speakers to the Front Speakers terminalsConnecting the rear and center speakers Connecting the subwooferConnecting Audio/Video Components Audio component connectionsVideo component connections If your audio components have a Compu LINK-3 terminalDVD player connection If your audio components have an AV Compu Link terminalConnecting the Power Cord Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and OffBasic Operations On the front panelBasic Operations From the remote control onlyOn the front panel only To listen with only headphones Listening with HeadphonesRecording a Source Basic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes To cancel the Sleep TimerReceiver turns off automatically Press Sleep repeatedlyBasic Settings Selecting the Center Speaker SizeSmall LargeTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Selecting the FM Reception Mode Receiving Radio BroadcastsSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelUsing the Surround Processor On JVC 3D-PHONIC modeOn the DAP mode On surround modesUsing the Surround Processor Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRPress Control @ / #to adjust the effect level To cancel the 3D-PHONIC modePress Effect to select the effect level Each time you press the button, the level changes asPavilion Using the DAP ModesHall Select OFF in step DAP indicator goes off from the display To cancel the DAP modePress Rear L +/- to adjust the rear speaker Output level Effect Select Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This casePreparing for Surround Modes Press Surround so that the Control %/ Þ/ @ / #Prologic TheaterPress Control @/ # to select the center mode DelayWide NormalIf necessary, adjust the speaker output balance as follows Each time you press the button, the effect level changesPress Test to start checking the speaker output balance Press Effect to adjust the effect levelPress Test again to stop the test tone Using Surround Modes To cancel Surround modePrevious mode is recalled with its previous From the front panelSpeaker arrangements for DVD Multi playback Using the DVD Multi Playback ModeActivating the DVD Multi playback Using the DVD Multi Playback Mode Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingAV Compu Link Remote Control System Components with RCA pin plugsAutomatic Selection of TV’s Input Mode Automatic Power On/OffSee page 44 for details One-Touch Video PlayTo operate JVC audio components using this remote control Operating Other ComponentsStarts playing Starts playbackAfter pressing TV SOUND, you can perform To operate JVC video components using this remote controlFollowing operations on the TV TV/VIDEO TV Volume +Return Section Converter or satellite tuner Selects the channelEquipment requires pressing Enter Alternates between previouslyTry to operate your VCR by pressing VCR Power Release VCR in the Power sectionOperating Other Manufacturers’ Video Equipment Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierAM tuner FM tuner IHFGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM