JVC RX-664VBK manual Basic Operations, On the front panel only, From the remote control only

Page 18

Basic Operations

Adjusting the Volume

On the front panel:

 

MASTER VOLUME

To increase the volume, turn MASTER VOLUME

+

clockwise.

 

 

To decrease the volume, turn it counterclockwise.

When you turn MASTER VOLUME rapidly, the volume level also changes rapidly.

When you turn MASTER VOLUME slowly, the volume level also changes slowly.

From the remote control:

VOLUME

 

To increase the volume, press VOLUME +.

To decrease the volume, press VOLUME –.

Selecting the Front Speakers

On the front panel only:

1

2

 

 

SPEAKERS

When you have connected two sets of front speakers, you

_ON ÑOFF

can select which to use. Pressing SPEAKERS 1 or SPEAKERS 2 activiates the respective set of speakers.

To use the set of speakers connected to the FRONT SPEAKERS 1 terminals, press

SPEAKERS 1 to set it in the _ON position, and press SPEAKERS 2 to set it in the Ñ OFF position.

To use the set of speakers connected to the FRONT SPEAKERS 2 terminals, press

SPEAKERS 2 to set it in the _ON position, and press SPEAKERS 1 to set it in the Ñ OFF position.

To use both set of speakers, press both SPEAKERS 1 and 2 to set them in the _ON position.

To use neither set of speakers, press both SPEAKERS 1 and 2 to set them in the Ñ OFF position.

Muting the Sound

From the remote control only:

 

Press MUTING to turn off the sound through all

MUTING

 

speakers and headphones connected.

 

“MUTE” appears on the display and the volume turns off.

To restore the sound, press MUTING again.

Turning MASTER VOLUME or pressing VOLUME +/– also restores the sound.

CAUTION:

Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

Note:

The volume level can be adjusted within the range of “0” (minimum) to “62” (maximum).

Notes:

When only one set of the front speakers is connected to either the FRONT SPEAKERS 1 or 2 terminals, do not press both SPEAKERS 1 and 2 to set them in the _ON position. If you do, no sound comes out of the front speakers.

The SPEAKERS 1 and 2 buttons do not affect the sound output of the center and rear speakers.

15

Image 18
Contents RX-664VBK To Reduce the Risk of Electric Shock For actual setting procedures, see pages 26 to Center Speaker Level Rear Speaker Level Effect LevelTable of Contents Remote Control Parts IdentificationFront Panel Easy Set Up & Operations For Reproducing Surround Sound with your VCRTurn on the power Easy Set Up & Operations For Reproducing DVD Multi Playback with your DVD playerAudio Sound VCR Control Disc Locations Getting StartedGeneral Handling the receiverConnecting the FM and AM Antennas FM Antenna ConnectionsAM Antenna Connections Getting Started Connecting the front speakersConnecting the Speakers Connect the front speakers to the Front Speakers terminalsConnecting the rear and center speakers Connecting the subwooferVideo component connections Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalDVD player connection If your audio components have an AV Compu Link terminalConnecting the Power Cord Putting Batteries in the Remote ControlBasic Operations From the remote controlTurning the Power On and Off On the front panelFrom the remote control only Basic OperationsOn the front panel only Listening with Headphones To listen with only headphonesRecording a Source Listening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep TimerReceiver turns off automatically When the shut-off time comesTo cancel the Sleep Timer Press Sleep repeatedlySmall Basic SettingsSelecting the Center Speaker Size LargeTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsTo cancel a stored preset station To tune in a preset stationPress 10 keys to select a preset channel number Selecting the FM Reception Mode Receiving Radio BroadcastsUsing the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelOn the DAP mode Using the Surround ProcessorOn JVC 3D-PHONIC mode On surround modes3DACTION Using the Surround ProcessorUsing JVC 3D-PHONIC Modes 3DTHEATRPress Effect to select the effect level Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Each time you press the button, the level changes asUsing the DAP Modes PavilionHall To cancel the DAP mode Select OFF in step DAP indicator goes off from the displayPress Rear L +/- to adjust the rear speaker Output level Effect Speaker Arrangements for Surround Modes Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode This casePrologic Preparing for Surround ModesPress Surround so that the Control %/ Þ/ @ / # TheaterWide Press Control @/ # to select the center modeDelay NormalIf necessary, adjust the speaker output balance as follows Each time you press the button, the effect level changesPress Effect to adjust the effect level Press Test to start checking the speaker output balancePress Test again to stop the test tone Previous mode is recalled with its previous Using Surround ModesTo cancel Surround mode From the front panelUsing the DVD Multi Playback Mode Speaker arrangements for DVD Multi playbackActivating the DVD Multi playback Using the DVD Multi Playback Mode Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingAV Compu Link Remote Control System Components with RCA pin plugsSee page 44 for details Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlayStarts playing To operate JVC audio components using this remote controlOperating Other Components Starts playbackTo operate JVC video components using this remote control After pressing TV SOUND, you can performFollowing operations on the TV TV Volume + TV/VIDEOReturn Equipment requires pressing Enter Section Converter or satellite tunerSelects the channel Alternates between previouslyRelease VCR in the Power section Try to operate your VCR by pressing VCR PowerOperating Other Manufacturers’ Video Equipment Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF AM tunerGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM