Weider 831.159730 user manual Small Pulley Bracket is oriented exactly as shown

Page 12

21.Remove both 3 1/2” Pulleys (24) from the pre-assem- bled Small Pulley Bracket (22).

Wrap the Butterfly Cable (73) around a 3 1/2” Pulley

(24)in the direction shown. Attach the Pulley to the Small Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt

(57)and a 3/8” Nylon Locknut (50). Make sure the

Small Pulley Bracket is oriented exactly as shown.

22.Wrap the Butterfly Cable (73) around a “V”-Pulley

(27)in the direction shown. Attach the “V”-Pulley and a Large Cable Trap (32) to the bracket on the back of the Butterfly Upright (1) with a 3/8” x 2 1/2” Bolt

(53)and a 3/8” Nylon Locknut (50). Make sure the

Large Cable Trap is oriented as shown.

23.Attach the Butterfly Cable (73) to the bracket on the Right Butterfly Arm (11) with a 3/8” x 1” Bolt (84) and two 3/8” Nylon Jamnuts (63). Note: The loop on the

Cable and the two Nylon Jamnuts must be mount- ed underneath the welded bracket.

24.Identify the Ab Cable (74). It is approximately 224” long, and it has a ball on one end and a threaded shaft on the other. You will start by attaching the end of the Cable with the ball.

Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in the direction shown. Place two Pulley Covers (47) over the Pulley, so that the slots in the Pulley Covers are placed over the Cable. Attach the Pulley and Pulley Covers to the indicated hole in the Butterfly Upright (1) with a 3/8” x 3 3/4” Bolt (59), two 3/8” Flat Washers (48), and a 3/8” Nylon Jamnut (63). Make sure the Cable is between the Pulley and the welded pin on the Upright.

21

 

 

 

 

 

 

 

73

 

 

 

 

24

 

 

 

 

 

50

 

57

 

 

 

 

 

 

 

22

22

 

 

 

 

53

 

 

Bracket

 

 

 

 

 

 

 

 

 

50

 

27

 

 

 

73

32

 

 

 

 

 

 

 

 

 

1

 

 

23

 

 

 

 

 

 

84

Bracket

 

 

 

 

 

11

63

 

 

 

 

 

73

 

 

 

 

 

24

 

 

 

 

59

 

 

 

 

48

 

 

 

 

 

 

47

 

 

Pin

 

 

 

 

74

 

24

63

 

 

 

48

 

 

1

 

 

 

12

Image 12
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important PrecautionsDimensions Before You BeginAssembly Four Stages of the Assembly ProcessFrame Assembly Locknuts yetPage Locknuts yet Nylon Locknuts yet Nylon Locknut the Leg Press Lever must pivot easilyGroove Pin Grooves Brackets Arm Assembly Locate and open the parts bag labeled ARM AssemblyCable Assembly Large Cable Trap is oriented as shownSmall Pulley Bracket is oriented exactly as shown Pulley Plates are oriented as shown Bracket is oriented as shownMake sure the Cable Trap is oriented as shown Page Remove a Pro Pulley 26 from the bag labeled Pulley BAG Cable Trap is oriented as shownRemove a Pro Pulley 26 from the bag labeled Pulley BAG Page Make sure the Cable Trap is oriented as shown Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyMiscellaneous Assembly Leg Press Plate must be on the upper edgeWeider Cable Diagrams Press Cable Adjustment Changing the Weight SettingAdjusting the Leg Press Plate Trouble-shooting and Maintenance Weight Resistance Chart High Arm Leg Butterfly Curl Ab PulleyPress Lbs Leg RaisePage Part Identification Chart-Model No R0800APart List-Model No Qty DescriptionExploded Drawing-Model No QUESTIONS? Model No