Weider 831.159730 user manual

Page 6

3.Place the bracket on the lower end of the Butterfly Upright (1) over the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base (4). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts. Do not tighten the Nylon Locknuts yet.

4.Press three 2” Square Inner Caps (28) into the Butterfly Top Frame (33). Press two 1” Round Inner Cap (86) into the top of the Butterfly Top Frame (33).

Attach the Butterfly Top Frame (33) to the indicated bracket at the top of the Butterfly Upright (1) with two 5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2” center holes (93), and two 5/16” Nylon Locknuts (64).

5.Attach the Butterfly Seat Frame (14) to the Front Leg (20) with two 5/16” x 2 3/4” Bolts (89), two 5/16” Washers (36), and two 5/16” Nylon Locknuts (64). Do not tighten the Nylon Locknuts yet.

Slide the bracket on the Front Leg (20) onto the two 5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base

(4). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts. Do not tighten the Nylon Locknuts yet.

Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 5/16” x 2 3/4” Bolts (89), two 5/16” Washers (36) and two 5/16” Nylon Locknuts (64). Do not tighten the Nylon Locknuts yet.

3

 

 

 

 

1

 

 

 

 

64

 

4

 

 

 

 

92

 

4

89

 

86

 

 

93

28

 

 

28

 

 

 

33

 

 

 

64

 

 

28

 

1

 

 

5

64

64

1

 

 

 

 

 

 

89

36

 

14

64

 

 

36

 

 

 

 

64

 

 

89

64

 

 

20

 

 

 

 

 

 

4

 

 

92

 

6

Image 6
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important PrecautionsDimensions Before You BeginAssembly Four Stages of the Assembly ProcessFrame Assembly Locknuts yetPage Locknuts yet Nylon Locknuts yet Nylon Locknut the Leg Press Lever must pivot easilyGroove Pin Grooves Brackets Arm Assembly Locate and open the parts bag labeled ARM AssemblyCable Assembly Large Cable Trap is oriented as shownSmall Pulley Bracket is oriented exactly as shown Pulley Plates are oriented as shown Bracket is oriented as shownMake sure the Cable Trap is oriented as shown Page Remove a Pro Pulley 26 from the bag labeled Pulley BAG Cable Trap is oriented as shownRemove a Pro Pulley 26 from the bag labeled Pulley BAG Page Make sure the Cable Trap is oriented as shown Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyMiscellaneous Assembly Leg Press Plate must be on the upper edgeWeider Cable Diagrams Press Cable Adjustment Changing the Weight SettingAdjusting the Leg Press Plate Trouble-shooting and Maintenance Press Lbs Weight Resistance ChartHigh Arm Leg Butterfly Curl Ab Pulley Leg RaisePage Part Identification Chart-Model No R0800APart List-Model No Qty DescriptionExploded Drawing-Model No QUESTIONS? Model No