Weider 831.159730 user manual Frame Assembly, Locknuts yet

Page 5

Frame Assembly

1.Before beginning, make sure that you have read and understood the information on page 4.

Locate and open the parts bag labeled “FRAME ASSEMBLY.”

See drawing 1a. Press a 2” Square Inner Cap (28) into each end of the Butterfly Base (4). Press two 2” Square Inner Caps (28) into the Weight Base (5).

Insert four 5/16” x 2 1/2” Carriage Bolts (92) up through the indicated holes in the Butterfly Base (4). Insert a 3/8” x 3 1/2” Carriage Bolt (95) up through the hole at the end of the Butterfly Base. Note: If the

Bolts fall out, secure them by putting a small piece of tape over the head of each Bolt. Place the Butterfly Base flat on the floor.

See drawing 1b. Attach the Weight Base (5) to the Butterfly Base (4) with two 5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2” center holes (93), and two 5/16” Nylon Locknuts (64). Do not tighten the Nylon

Locknuts yet.

Note: There are three kinds of Support Plates. The main difference between them is the distance between the holes. When you need a Support Plate, find the type with holes that will fit over the Bolts you are using.

2.See drawing 2a. Press a 2” Square Inner Cap (28) into the end of the Press Base (6).

Attach a 3 1/2” Pulley (24) to each of the brackets on the Weight Base (5) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Jamnut (63).

Insert four 5/16” x 2 1/2” Carriage Bolts (92) up through the indicated holes in the Press Base (6). Insert a 3/8” x 2 1/2” Carriage Bolt (101) and a 3/8 x 4” Carriage Bolt (102) up through the indicated holes at the end of the Press Base (6).

See drawing 2b. Attach the Press Base (6) to the Weight Base (5) with two 5/16” x 2 3/4” Bolts (89), a Support Plate with 3 1/2” center holes (93), and two 5/16” Nylon Locknuts (64). Do not tighten the Nylon

Locknuts yet.

1a

 

 

 

 

 

28

 

 

 

 

28

 

4

 

28

 

 

 

 

 

95

 

 

92

5

 

 

92

 

 

 

 

28

 

 

 

1b

89

 

 

 

 

 

 

93

64

 

 

4

 

64

 

 

 

5

 

 

 

2a

5

24

 

 

 

 

 

63

63

 

57

 

28

 

57

 

 

 

 

 

 

6

102

 

 

 

 

 

92

101

 

 

92

 

2b

 

 

 

 

 

64

 

5

 

 

 

 

64

 

93

 

 

 

6

 

 

 

 

 

 

89

5

Image 5
Contents SEARS, Roebuck and CO. Hoffman ESTATES, IL Model No Serial No Important Precautions Table of ContentsBefore You Begin DimensionsFour Stages of the Assembly Process AssemblyLocknuts yet Frame AssemblyPage Locknuts yet Nylon Locknut the Leg Press Lever must pivot easily Nylon Locknuts yetGroove Pin Grooves Brackets Locate and open the parts bag labeled ARM Assembly Arm AssemblyLarge Cable Trap is oriented as shown Cable AssemblySmall Pulley Bracket is oriented exactly as shown Make sure the Cable Trap is oriented as shown Pulley Plates are oriented as shownBracket is oriented as shown Page Cable Trap is oriented as shown Remove a Pro Pulley 26 from the bag labeled Pulley BAGRemove a Pro Pulley 26 from the bag labeled Pulley BAG Page Make sure the Cable Trap is oriented as shown Page Locate and open the parts bag labeled Seat Assembly Seat AssemblyLeg Press Plate must be on the upper edge Miscellaneous AssemblyWeider Cable Diagrams Press Cable Adjusting the Leg Press Plate AdjustmentChanging the Weight Setting Trouble-shooting and Maintenance High Arm Leg Butterfly Curl Ab Pulley Weight Resistance ChartPress Lbs Leg RaisePage R0800A Part Identification Chart-Model NoQty Description Part List-Model NoExploded Drawing-Model No Model No QUESTIONS?