52.Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the center hole in a Seat Plate (65). Attach the Seat Plate to a Seat (13) with two 1/4” x 3/4” Bolts (49).
Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the indi- cated hole in the Butterfly Seat Frame (14) and secure it with a 1/4” Flat Washer (71) and a 1/4” Nylon Locknut (68). Secure the other end of the Seat
(13)with a 1/4” x 2 1/2” Bolt (79) and a 1/4” Flat Washer (71).
Attach the other Seat (13) to the Press Seat Frame (7, not shown) in the same manner.
Miscellaneous Assembly
53.Press 3/4” Round Inner Caps (43) into the ends of the Pad Tube (42) and the indicated tube on the Front Leg (20).
Insert the Pad Tube (42) into the indicated hole in the Small Leg Lever (41). Slide Foam Pads (30) onto the ends of the Pad Tube and the tube on the Leg Lever.
54.Press a 1 3/4” Square Inner Cap (35) into the indicat- ed end of the Adjustment Tube (90).
Attach the Adjustment Tube (90) to the bracket (not visible in the drawing) on the back of the Leg Press Plate (55) with a 5/16” x 2 1/2” Bolt (87), two 5/16” Washers (36), and a 5/16” Nylon Locknut (64).
Attach the Leg Press Plate (55) to the Leg Press Lever (83) by placing the Adjustment Tube (90) into the bracket on top of the Leg Press Lever and secur- ing it with the Lock Pin (91). Note: The lip on the
Leg Press Plate must be on the upper edge.
55.Attach the Curl Pad (105) to the Curl Post (104) with two 1/4” x 3/4” Bolts (49).
52 |
|
|
|
|
|
|
| 13 |
|
|
|
| 45 |
|
|
|
|
|
| |
|
|
| 65 |
|
|
|
|
| 14 |
| 49 |
|
|
|
|
|
|
|
| |
|
|
|
| 71 |
|
|
|
|
|
|
|
| 68 |
|
|
| 71 | 79 |
|
|
53 | 43 | 30 | Tube |
|
| |
|
|
| ||||
| 41 |
|
| 30 |
|
|
|
|
|
|
|
| |
43 |
|
|
|
|
| |
| 30 |
|
|
| 43 | |
|
|
|
| 20 |
|
|
|
|
| 42 |
|
| 43 |
|
|
|
|
|
| |
|
|
|
| 30 |
|
|
54 |
|
|
| 91 |
|
|
|
|
|
|
| 35 | |
|
|
|
|
|
| |
|
| 64 | 36 |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| 90 |
|
|
|
| 36 | 87 | |
|
|
|
|
| ||
| 55 |
|
|
|
|
|
|
| 83 |
|
|
|
|
55 |
|
|
|
|
|
|
| 105 |
|
|
|
|
|
|
|
|
|
|
| 49 |
|
|
|
|
|
| 104 |
21