Weider 831.159730 Nylon Locknuts yet, Nylon Locknut the Leg Press Lever must pivot easily

Page 8

9.Press a 2” Square Inner Cap (28) into the Press Seat Frame (7).

Slide the bracket on the Press Seat Frame (7) onto the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Press Base (6). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts. Do not tighten the

Nylon Locknuts yet.

Attach the Press Seat Frame (7) to the Press Upright

(2) with two 5/16” x 2 3/4” Bolts (89), two 5/16” Washers (36), and two 5/16” Nylon Locknuts (64). Do not tighten the Nylon Locknuts yet.

10.Lubricate the 3/8” x 3” Bolt (88). Attach the Leg Press Lever (83) to the Press Base (6) with the Bolt and a 3/8” Nylon Locknut (50). Do not overtighten the

Nylon Locknut; the Leg Press Lever must pivot easily.

11.Place two Weight Bumpers (51) over the indicated holes in the Weight Base (5). Slide a Weight Guide

(15)into each of the holes.

Attach the indicated Weight Guide (15) to the Weight Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat Washers (48), and a 3/8” Nylon Locknut (50).

Slide six Weights (21) onto the Weight Guides (15).

Make sure the Weights are turned so the pin grooves point towards the floor.

Press a Weight Tube Bumper (18) into the lower end of the Short Weight Tube (17). Slide the Weight Tube into the center holes in the Weights (21).

Slide a Top Weight (16) onto the Weight Guides (15).

Note: Make sure the Top Weight is turned so the groove fits over the welded pin on the Weight Tube (17).

8

9

 

89

36

 

 

 

 

7

 

64

 

 

 

 

 

 

36

28

 

 

 

 

 

89

 

64

64

 

2

 

 

 

 

 

 

 

 

6

 

92

 

 

10

 

 

 

 

83

 

 

 

 

 

6

 

50

 

Lubricate

 

 

 

88

11

15

 

 

 

 

 

 

16

 

 

 

Groove

 

 

 

Pin

 

 

 

17

 

 

 

 

18

 

 

21

 

 

Pin

 

 

 

Grooves

 

 

 

 

51

 

 

 

48

 

 

 

 

50

 

5

 

 

 

48

 

 

 

46

 

 

Image 8
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important PrecautionsDimensions Before You BeginAssembly Four Stages of the Assembly ProcessFrame Assembly Locknuts yetPage Locknuts yet Nylon Locknuts yet Nylon Locknut the Leg Press Lever must pivot easilyGroove Pin Grooves Brackets Arm Assembly Locate and open the parts bag labeled ARM AssemblyCable Assembly Large Cable Trap is oriented as shownSmall Pulley Bracket is oriented exactly as shown Make sure the Cable Trap is oriented as shown Pulley Plates are oriented as shownBracket is oriented as shown Page Remove a Pro Pulley 26 from the bag labeled Pulley BAG Cable Trap is oriented as shownRemove a Pro Pulley 26 from the bag labeled Pulley BAG Page Make sure the Cable Trap is oriented as shown Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyMiscellaneous Assembly Leg Press Plate must be on the upper edgeWeider Cable Diagrams Press Cable Adjusting the Leg Press Plate AdjustmentChanging the Weight Setting Trouble-shooting and Maintenance Weight Resistance Chart High Arm Leg Butterfly Curl Ab PulleyPress Lbs Leg RaisePage Part Identification Chart-Model No R0800APart List-Model No Qty DescriptionExploded Drawing-Model No QUESTIONS? Model No