FRAME ASSEMBLY | 1 |
|
|
|
| |
|
|
|
|
| ||
1. Before beginning assembly, be sure that you |
|
|
|
|
| |
have read and understand the information in |
|
|
|
|
| |
the box on the previous page. |
|
|
|
|
| |
Press a 50mm Square Outer Cap (51) onto each |
|
| 56 |
|
| |
|
|
|
|
| ||
end of the Stabilizer (5). Press a 50mm Square |
|
|
|
|
| |
Inner Cap (27) into the end of the Base (4). |
|
|
|
|
| |
Insert two M8 x 67mm Carriage Bolts (14) up |
|
|
|
|
| |
through the Stabilizer (5). Insert two M8 x 63mm |
|
|
|
|
| |
Carriage Bolts (1) up through the Base (4). |
|
| 3 |
|
| |
Slide the bracket on the end of the Base (4) onto |
|
|
|
|
| |
the M8 x 67mm Carriage Bolts (14) in the |
|
|
|
|
| |
Stabilizer (5). Slide the Rear Upright (56) onto the |
|
|
|
|
| |
Carriage Bolts. Hand tighten an M8 Nylon |
|
| 51 |
|
| |
Locknut (3) onto each Carriage Bolt. Note: Be |
| 5 |
|
|
| |
sure the indents around the holes in the |
|
|
|
| ||
|
|
|
|
| ||
Stabiliser are on the bottom. |
|
| 4 |
|
| |
| 51 | Indents | 14 |
|
| |
|
|
|
| |||
|
|
| 1 |
| 27 | |
|
|
|
|
| ||
2. Refer to drawing 2a. Press a 25mm Round Inner | 2 |
| 2a | 70 | 49 | |
Cap (49) into each end of the weight tube on the | 19 | |||||
|
|
| ||||
|
|
|
| |||
Weight Carriage (19). Note: The Square Slider |
|
|
|
| ||
|
|
| 19 |
| ||
Bushings (70) should be |
|
| 49 | 70 | ||
|
|
| ||||
Weight Carriage and the Weight Stop (67). |
|
|
|
| ||
| 70 |
|
|
| ||
|
|
|
|
| ||
Turn the Weight Stop (67) so that the hole in the |
| 67 | Hole | 70 | 67 | |
Weight Stop is oriented in the same direction as |
| |||||
|
| |||||
the hole in the bottom of the Rear Upright (56). |
|
|
|
|
| |
Make sure that the Square Slider Bushing (70) |
|
|
|
|
| |
is above the Weight Stop. Slide the Weight Stop |
|
|
|
|
| |
onto the Rear Upright. |
| 56 | 42 |
|
| |
|
|
|
|
| ||
Refer to drawing 2b. Secure the Weight Stop |
|
|
|
|
| |
(67) to the hole near the base of the Rear Upright |
|
|
|
|
| |
(56) with an M8 x 70mm Bolt (11) and an M8 |
|
|
|
|
| |
Nylon Locknut (3). Slide the Weight Carriage (19) |
|
|
|
|
| |
onto the Rear Upright. |
|
|
| 65 |
| |
Press a 25mm Square Inner Cap (65) into the |
|
| Hole |
|
| |
|
|
|
|
| ||
Front Upright (42). Slide the Front Upright onto |
|
|
|
|
| |
the M8 x 63mm Carriage Bolts (1) in the Base |
|
| 3 |
|
| |
(4). Hand tighten an M8 Nylon Locknut (3) onto | 2b | 56 |
|
|
| |
each Carriage Bolt. Do not tighten the Nylon | 4 |
|
| |||
|
|
|
| |||
Locknuts yet. | 19 | 67 |
|
|
| |
|
|
|
| |||
|
| 1 |
|
| ||
|
|
|
|
| ||
| 3 |
| 11 |
|
|
6