Weider WESY17011 user manual Adjustment, Adding Weights to the Weight Carriage

Page 16

ADJUSTMENT

The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPOR-

TANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the correct start- ing position for the exercise to be performed. If there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise will be reduced.

ADDING WEIGHTS TO THE WEIGHT CARRIAGE

To add resistance to your workout, slide an equal amount of weight (not included) onto each side of the weight tube on the Weight Carriage (19). Make sure that the weights are pushed against the stops. Note:

Due to the cables and pulleys, the actual amount of resistance at each exercise station may vary from the amount of weight used. Use the WEIGHT RESISTANCE CHART on page 18 to find the actu- al amount of resistance at each weight station.

WARNING: Do not place more than 125 pounds on the Weight Carriage (19).

ATTACHING THE LAT BAR OR NYLON STRAP TO THE HIGH OR LOW PULLEY STATION

Attach the Lat Bar (54) to the Long Cable (58) or Short Cable (not shown) with a Cable Clip (53). For some exercises, the Chain (52) should be attached between the Lat Bar and the Cable with two Cable Clips. Adjust the length of the Chain between the

Lat Bar and the Cable so the Lat Bar is in the cor- rect starting position for the exercise to be per- formed.

The Nylon Strap (not shown) can be attached in the same manner.

ATTACHING AND REMOVING THE SEAT

Set the bracket on the Seat Frame (36) onto the indi- cated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the M8 x 67mm Carriage Bolt (14) and the Seat Knob (40).

For some exercises, the Seat (13) must be removed. First, be sure that the chain is not attached to the leg lever (see ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION below). Next, remove the Seat Knob (40) and the M8 x 67mm Carriage Bolt

(14)from the Seat Frame (36). Finally, lift the Seat Frame off of the Front Upright (42).

19

 

Weight

 

Tube

 

Stops

 

53

 

58

53

 

52

 

 

54

40

 

36

13

42

 

14

 

Pin

 

16

 

Image 16
Contents Model No. WESY17011 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Dimensions Before YOU BeginAssembly Make Assembly Easier for YourselfFrame Assembly Each Carriage Bolt. Do not tighten the Nylon Locknuts yetARM Assembly Tighten the Nylon Locknuts used in stepsCable Assembly Cable Trap is positioned to hold the Cable in place Bolt and the Nylon Locknut are tight Parts are oriented as shown. Do not tighten Nylon Locknuts yetUpright 42. See the inset drawing. Be sure Inset shows viewInset shows view Seat Assembly Tighten the Nylon Locknut the Leg Lever Must pivot freelyPage Page Adding Weights to the Weight Carriage AdjustmentAttaching and Removing the Seat Attaching the Curl PAD to the Seat Frame Attaching the LEG Lever to the LOW Pulley StationAttaching the LAT BAR to the LEG Lever Weight Resistance Chart Weight on Press ARM Butterfly ARM LOW Pulley High PulleyLbs LEG LeverTROUBLE-SHOOTING and Maintenance Tightening the CablesCable Diagram Long CableTOP View Long U-Bracket Short CablePage Part LIST-Model No. WESY17011 Qty DescriptionR0802B Part Identification CHART-WESY17011 Page 19mm Round Inner Cap 25mm Retainer Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT