| ARM ASSEMBLY | 11 |
|
|
|
|
| 10 |
|
| |
|
|
|
|
| |
11. | Locate and open the parts bag labeled “ARM |
|
| 20 | 40 |
|
|
|
| ||
| ASSEMBLY.” |
|
|
|
|
| Attach the Leg Press Plate (11) to the Adjustment | 62 |
|
|
|
|
|
|
|
| |
| Tube (10) with an M8 x 60mm Bolt (62), two M8 |
|
|
|
|
| Washers (20), and an M8 Nylon Locknut (40). |
|
|
| 11 |
| Make sure that the Leg Press Plate and |
| Obtuse |
| |
| Adjustment Tube are oriented as shown. |
| Angle |
|
|
12. | Attach the Adjustment Tube (10) to the Leg Press | 12 |
|
|
|
| Arm (9) with the Lock Pin (73). |
| 10 | ||
| 73 |
| |||
|
|
| |||
|
|
|
|
| |
|
|
|
|
| 11 |
|
|
| 9 |
|
|
13. | Attach the Leg Press Bumper (53) to the Front | 13 |
|
|
|
| Seat Frame (8) with the M5 x 25mm Tap Screw |
|
|
| |
|
|
|
|
| |
| (72). |
|
|
|
|
| Lubricate the M10 x 80mm Bolt (71) with grease. |
| 8 |
|
|
| Attach the Leg Press Arm (9) to the Press Base |
|
| 9 |
|
| (13) with the Bolt and an M10 Nylon Locknut (42). |
|
|
| |
|
|
|
|
| |
| Do not overtighten the Locknut; the Leg Press |
|
| 53 |
|
| Arm must be able to pivot easily. |
|
| 42 | |
|
|
|
| ||
|
|
|
| 72 | |
|
|
|
|
| |
|
|
|
|
| Lubricate |
|
|
| 13 |
| 71 |
|
|
|
|
| |
14. | Press a 25mm x 22mm Plastic Bushing (54) onto | 14 |
|
|
|
| each welded spacer on the Press Frame (12). |
|
|
|
|
| Slide the Press Frame onto the Press Base (13) |
|
|
|
|
| so that the Plastic Bushings are aligned with the |
|
|
|
|
| indicated tube. Note: This will be a tight fit. |
|
|
|
|
| Make sure that the high hole is on the side |
|
|
| Tube |
| shown. |
|
|
| |
|
|
|
|
| |
| Lubricate the M10 x 195mm Bolt (52) with | High |
| 12 52 |
|
| Hole |
|
|
| |
| grease. Attach the Press Frame (12) to the Press |
|
|
| |
| Welded |
|
| 13 | |
| Base (13) with the Bolt and an M10 Nylon |
|
| ||
|
|
|
| ||
| Spacers |
|
|
| |
| Locknut (42). Do not overtighten the Locknut; |
|
| Lubricate | |
|
|
|
| ||
| the Press Frame must be able to pivot easily. | 42 |
|
|
|
|
| 54 |
| ||
|
|
|
| ||
|
| 9 |
|
|
|