English
Common Operations
Turning On or Off the Power |
|
|
|
|
|
|
|
| 3 Turn ¢ / 4 to |
|
|
|
|
|
|
|
|
| adjust the |
To turn on the unit, press (or | STANDBY |
|
|
|
|
| |||
|
|
|
|
| minutes, then | ||||
|
|
|
| ||||||
STANDBY/ON on the remote |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| press | |
control) so that the STANDBY lamp |
|
|
|
|
|
|
|
| |
goes off. |
|
|
|
|
|
|
|
| SET/DISPLAY. |
PR | E |
SET |
SET
/DISPLAY
To turn off the unit (standby), press | STANDBY | ||
(or STANDBY/ON on the |
|
|
|
|
|
| |
remote control) again so that the |
|
|
|
STANDBY lamp lights up. |
|
|
|
•A little power is always consumed even while the unit is on standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
When you unplug the AC power cord or if a power failure occurs
The clock is reset to “0:00” immediately, while the tuner preset stations (see page 12) will be erased in a few days.
Setting the Clock
Before operating the unit any further, first set the clock built in this unit. “0:00” will flash on the display until you set the clock.
• You can set the clock whether the unit is on or off.
On the unit ONLY:
1 Press CLOCK/TIMER.
The hour digits start flashing on the display. | CLOCK |
| /TIMER |
2 Turn ¢ / 4 to | PRESET |
adjust the hour, | SET |
then press | /DISPLAY |
| |
SET/DISPLAY. |
|
The minute digits start |
|
flashing on the |
|
display. |
|
To correct the hour after pressing | CANCEL |
SET/DISPLAY, press CANCEL/DEMO. | /DEMO |
| |
The hour digits start flashing again. |
|
|
|
To check the clock time while playing a source
Press and hold SET/DISPLAY.
•Each time you press and hold the button, the source indication and the clock time alternate on the display.
To adjust the clock again
If you have set the clock before, press CLOCK/TIMER repeatedly until the clock setting mode is selected.
•Each time you press the button, the clock/timer setting modes change as follows:
DAILY TIMER REC
(Daily Timer setting)
Canceled |
|
| Clock |
|
| TIMER |
|
| |||||
|
|
| setting | (Recording Timer setting) |
(The hour digits start flashing.)
•When you unplug the AC power cord or if a power failure occurs
The clock loses its setting and is reset to “0:00.” If this happens, set the clock again.
•The clock may gain or loss 1 to 2 minutes per month If this happens, reset the clock.
Selecting the Sources
Press one of the source
When you press one of the source buttons (FM/AM,
CD 3/8, TAPE 2 3, and AUX), the unit turns on and starts playing the source if it is ready.
•To listen to the FM/AM broadcasts, press FM/AM. (See page 12.)
•To play back discs, press CD 3¥8. (See pages 13 – 19.)
•To play back tapes, press TAPE 2 3. (See page 20.)
•To select an external component as the source, press AUX.
AUX | FM / AM | TAPE |
| CD | |
|
|
|
|
|
|
9