2. Attach a Wheel (31) to the outside of the Base (1) | 2 |
|
|
|
|
|
|
|
with a 3/8” x 4 1/4” Bolt (81), three 3/8” Washers |
|
|
|
|
|
|
| |
(75), and a 3/8” Nylon Locknut (76). Do not over- |
|
|
|
|
|
|
|
|
tighten the Locknut; the Wheel must be able |
|
|
|
|
|
|
|
|
to turn easily. |
|
|
| 76 | 75 |
|
| |
Attach the other Wheel (not shown) in the |
|
|
| 75 |
| |||
same manner. |
|
|
|
|
|
| 81 | |
|
|
|
| 1 | 31 | |||
3. Press a 1 1/2” x 2 1/2” Inner Cap (41) into each | 3 |
|
|
| ||||
|
|
|
|
|
|
| ||
end of the Cross Tube (11). |
| 3 | 41 |
|
|
| ||
Orient the Cross Tube (11) as shown, with the | 23 |
|
| 75 | 47 | |||
welded tubes at the bottom. Attach the Foot Plate |
|
|
|
|
|
| ||
(23) and the Cross Tube to the Upright (3) with |
|
|
|
|
|
|
|
|
two 3/8” x 5 1/2” Carriage Bolts (73), two 3/8” |
|
|
|
|
|
|
| 41 |
Washers (75), and two 3/8” Nuts (47). Do not |
|
|
|
|
|
|
| |
insert a bolt into the top hole in the Foot Plate | 73 |
|
|
|
|
| 11 |
|
yet. |
|
|
|
|
|
| ||
|
|
|
|
|
|
| Welded | |
4. Press two 2 1/4” Round Outer Caps (27) onto the | 4 |
|
|
|
|
| Tube | |
ends of the Front Leg (6). |
|
| 5 |
|
|
|
| |
Orient the Bench Rail (5) as shown. Slide the Rail |
|
|
|
|
|
|
| |
Bracket (105) into the indicated end of the Bench |
| 105 |
|
|
|
|
|
|
Rail, and align the holes in the Bracket with the |
|
| Holes |
|
|
| ||
holes in the Bench Rail. | 27 | 52 |
|
|
|
| ||
Orient the Front Leg (6) as shown. Attach the |
| 52 |
|
|
|
| ||
Front Leg to the Bench Rail (5) with the Rail |
|
|
|
|
|
|
|
|
Bracket (105), four 5/16” x 1” Button Screws (46), |
|
|
| 46 |
|
|
|
|
and four 5/16” Split Washers (52). |
| 46 |
| 27 |
|
| ||
|
| 6 |
|
|
| |||
|
|
|
|
|
| |||
5. See the inset drawing. Snap the Seat Knob (45) | 5 |
|
|
|
|
|
|
|
into the Seat Carriage (12) and attach it with two |
|
|
| 13 |
|
|
| |
M6 x 16mm Screws (82) and two M6 Black Nylon |
|
|
|
|
|
|
| |
Locknuts (69). Make sure the slot in the Knob | Round |
|
|
|
|
|
| |
is aligned with the slot in the Seat Carriage. |
| 9 |
|
|
|
| ||
Orient the Seat (13) and the Seat Backing (9) as | End |
|
|
|
|
|
| |
shown. Attach the Seat and the Seat Backing to |
|
|
|
|
|
| 12 |
|
the Seat Carriage (12) with four M6 x 16mm |
|
|
|
|
|
|
| |
Screws (82). |
| 12 |
|
|
|
|
|
|
|
|
|
| Slot |
|
|
| |
|
|
|
|
|
|
|
| |
|
| 82 | 82 |
| 82 |
| 45 | 69 |
| 6 |
|
|
|
|
|
|
|