Electrolux 88840 manual Washing cycle complete/removing the washing, Programme Progress Display

Page 27

	Operating Instructions
3	The wash programme can be temporarily interrupted at any time by
	pressing the START/PAUSE button. It is then re-started by pressing the

button again.

Washing cycle complete/removing the washing

	Once the washing programme has come to an end, END illuminates on
	the Programme Progress Display.
3	If no buttons are pressed within about 3 minutes after the end of the
	programme, and the programme selector is not touched, the washing

machine goes into Stand-by mode. Only the END light remains on.

All other indicators on the control panel go off in order to save energy. You can press any button to cancel the Stand-by mode.

•If the EASY IRON programme was selected, the end of the programme is followed by the anti-crease phase, which lasts around 30 minutes. The multi-display indicates a remaining time of 1 minute and the END light is on. During the anti-crease phase, you can open the door and remove the washing at any time.

•If Spin Speed 0 (Rinse Hold) was selected, START/PAUSE flashes.

0 1. After a Rinse Hold, the water must first be drained:

– Either press the START/PAUSE button (the water is drained and the washing is spun according to the selected programme; spin speed can be changed by pressing the SPIN SPEED button even during the spin cycle), or

– turn the programme selector to DRAIN and press the START/PAUSE button (the water is drained without spinning), or

– turn the programme selector to SPIN or SHORT SPIN and press the START/PAUSE button (the water is drained and the washing is given a Spin/Short Spin).

When this stage of the programme is completed, the END light comes on.

2.Open the door.

The door can be opened as soon as DOOR/LIGHT is lit in green

(not if the Programme Protection is activated - see Section "Programme Protection").

3.Remove the washing.

4.Turn the programme selector to OFF.

5.After the wash, pull out the detergent dispenser drawer slightly to al- low it to dry. Leave the door slightly open to air the inside of the wash- ing machine.

27

Image 27

Contents ÖKO-LAVAMAT 88840 update Appliance Dear CustomerPages of this instruction book Future ownersContents Installation and connection instructions Page Safety Prior to initial start-upIntended Use General Safety Child SafetyPackaging When disposing of the washing machineDisposal Environmental tipsDescription of the Appliance Front viewDetergent dispenser drawer Programme selector Control panelSilk / P Handwash Wool / P HandwashPRE-WASH Pre-wash/Soaking Programme option buttonsTime Saver Programmable functionsConsumption values and programme times Wash Time DisplayAnce spin detection and foam detection Anti-flood Aqua Control + Aqua Alarm What does Update mean?Before the first wash Preparing for a wash cycleSorting and preparing the washing Types of washing and care symbols How much detergent and conditioner? Water softeningWater hardness details Running a washing cycle Brief instructionsAfter the washing programme has ended Bles Setting the wash programmeCannot be changed Selecting Spin Speed /Rinse HoldWOOL/PHandwash SILK/PHandwashSetting the Delay Timer/Soaking time Press the PRE-WASH button Press the Delay Timer buttonSoaking time For maximum loads, see Programme Tables Opening and closing the doorLoading the washing Automatically after approximately 3 minutesOr for water softener Adding detergent/conditionersCompartment for main wash deter- gent Compartment for Pre-wash detergent Soaking agentIf using liquid detergents/tablets If the Delay Timer is setStarting the wash programme Wash programme progress Programme Progress Display Washing cycle complete/removing the washingDetergent was used in the washing programme just com Washing Programme TablesSeparate Spinning Separate Rinsing/Conditioning/Starching/TreatingMaintenance and Cleaning Main door Maintenance WashTo run a maintenance wash Washing Machine DrumBefore cleaning the drain pump Cleaning the drain pumpTrouble Shooting What to do ifLow Machine is not level Machine is Water tap is not fully Turn the water tap on fully Opened If there are white residues on the washing If the washing results are not satisfactoryIf there are still grey stains on the washing If after the last rinse foam is still visibleHave a flat container on hand to catch the water Carrying out an emergency emptyingSupply first When the water is completely drainedUnlock feature Emergency unlocking of the doorTo set the additional rinse To cancel the additional rinseAdditional rinse cycle RINSE+ Helpful to rinse with extra waterTo set the water cooling function To cancel water coolingWater cooling Additional rinse cycle and water coolingTo cancel Variomatic Spin Variomatic spinTo set Variomatic Spin Setting the Programme Protection Cancelling the Programme ProtectionProgramme Protection Started Child Safety FeatureCancelling the child safety feature Washing programme can beInstallation Safety Precautions Installation and connection instructionsRemove transport packaging Installation of the applianceWhen transporting the unit with a sack trolley Transporting the applianceCover the hole with the cap G Installation on a Suspended Floor Installation-Site preparationLevelling the appliance Electrical Connection Measures not be observedEarth Blue Neutral Brown Live Disposed of safely Permanent ConnectionWater pressure Water connectionConnection to the machine Inlet Hose ConnectionWater Drainage Pump head of greater than 1m Technical data DimensionsDimensions in mm Great Britain Warranty conditionsPage Page Page Index Customer Care Service & Spare Parts0870 5 929 Help us to help you PNCAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG