Miele PW 6065 manual Auto load control Main wash water, Pre-wash water, Rinse water

Page 67

Settings - Supervisor level

Auto load control

Main wash water

The washer has an Auto load control. The water levels and the program running times are adjusted to the load size. If the load size automatic is turned off the program will always run as if for a full load.

The machine comes factory set with this option turned on.

Pre-wash water

The water type for the pre-wash can be selected (except for the program "Curtains"). The hot water intake will be only accessible at a wash temperature of 86°F (30°C) or higher.

The water type for the main wash can be selected (except for the programs "Woollens", "Silk" and "Curtains"). The hot water intake will be only accessible at a wash temperature of 86°F/30°C or higher.

The machine comes factory set with the water type "hot".

If the washer is not connected to hot water, the program running times will be extended and vary from the displayed remaining times.

If "Industrial water" is used, the washer must be refitted accordingly.

The machine comes factory set with the water type "hot".

Rinse water

The water type for the rinse in the programs "Cottons Hygiene", "Cottons Uni.", "Minimum iron", "Table linen", "Kitchen linen", "Towelling" and "Sluice" can be selected. The hot water intake will be only accessible at a wash temperature of 50°C or higher.

The machine comes factory set with the water type "hot".

If "Industrial water" is used, the washer must be refitted accordingly.

67

Image 67

Contents Operating manual Washer PW 6065 Plus Page Contents Contents Technical Safety Important Safety InstructionsUse Children Using accessoriesControl panel Guide to the washerMain menu Display functionProgram selection possibility Menu Program selection Settings JBasic menu of a wash program Before using for the first time Sort the laundry Using the washerGeneral tips Select a program Load the washerCoin mechanism Too little detergent may cause Adding detergentToo much detergent may cause At the end of a program Starting a programAdding/removing laundry during a wash program To cancel a programTo change a program To change a programDelicates 140F to 86F 60C to 30C Cottons Hygiene 203F to 158F 95C to 70CCottons Uni F to cold 60C to cold Minimum iron 140F to 86F 60C to 30CProgram guide Curtains 104F to cold 40C to cold Additional programsKitchen linen 203F to 140F 95C to 60C Table linen 140F to 86F 60C to 30CProofing 104F to 86F 40C to 30C Outerwear 104F to cold 40C to coldHygiene Disinfection programsSluice 167F 75C or Sluice 149F 65C Main wash Rinse Spin Program sequenceOuterwear Special features in the program sequence Anti-creaseHigh Spin Pre-rinseWithout final spin SpinSpin speed Rinse spinStarch Stop Accessing the sub-menu ExtrasOptions Pre-washIntensive Rinse StopWater plus Starting the Delay Start Delay StartSelect the sub-menu Delay Start Select the Delay Start timeSelect a program FavoritesSelecting/Changing a Favorite Basic menuSelecting the spin speed Selecting a temperatureAssigning a direct select button Saving a FavoriteNormal soiling DetergentWater hardness Water softenerDye removers / Fabric dyes Fabric softener, liquid starchCleaning the washer Cleaning and CareCleaning the detergent drawer Cleaning the inlet hose filters Cleaning the inlet hose filterCleaning the filter in the inlet valve Wash program cannot be started Frequently asked questionsGeneral problems with the washer Poor wash results Door will not open when the Door button is pressed Open the lint trap door Remove the toolMachines with a drain pump Open the drum door Machines with a drain valve Changing the light bulb Repairs After sales servicePC Update Optional accessoriesPage Installation Instructions Front view InstallationRear view Height Washer/ Dryer Stack Installation on a baseReinstallation of the machine lid Coin mechanismDo not lift the washer by the drum door Installation siteInstallation Removing the shipping strutsPull out the shipping strut out Pull the shipping strut outInstalling the shipping struts Leveling the washer Extension hoses MaintenanceWater connection Cold water connectionHot water connection Drain valve DrainageDrain pump For Canada only Electrical connectionTechnical Data Disposal of the packing materials Help to protect the environmentDisposal of an old appliance Menu Settings J To adjust standard settings Leaving the Settings menu Settings JOpening the menu Settings Selecting SettingsSuds cooling Language JSelecting the clock Time of dayContrast BrightnessMemory Temperature unitNot in current prog. Factory default StandbyEntering the code Settings Supervisor levelConfirming the code Save Sort languagesSupervisor level Intensive Water plusPre-wash water Auto load control Main wash waterRinse water Pre-wash temp. Cot Water level CottonsWater level Min. iron Wash time CottonsPre-wash Kitchen linen No. of programs DisinfectionHygiene SluicePre-rinse Min. iron Optimize energy Pre-rinse CottonsNo. rinses Cottons No. rinses min. ironNo detergent Leaving the Settings menuExternal dispenser Alteration rights reserved