AEG 88830 manual Start the washing program, If the delay timer is set

Page 24

Instructions for use

Start the washing program

0 1. Check that the water valve is open.

2. Start the washing program:

Press button START/PAUSE (MARCHE/PAUSE). The washing program is started or it starts after the set time expires.

3	If DOOR/LIGHT (PORTE/LUMIERE) flashes red when the button START/
	PAUSE (MARCHE/PAUSE) is pressed the filling door is not closed prop-
	erly. Press the filling door shut firmly and press button START/PAUSE
	(MARCHE/PAUSE) again.
	If the delay timer is set:
	The preset delay timer is counting, the remaining time until the
	program starts is shown in the multi-display (always in whole hours).
	During this time you can load washing or change / abort the time
	preselection.
	• Load washing: Press the START/PAUSE (MARCHE/PAUSE) button, the
	filling door can be opened. Then close the door and press button
	START/PAUSE (MARCHE/PAUSE) again.
	• Change or abort time preselection: Press the DELAY TIMER (DEPART
	DIFFERE) button as often as is necessary until the required time is
	displayed; when the program run time is displayed (display in
	minutes, e.g. 125) the washing program starts without delay.
3	While the time preselection counts the washing machine switches to
	the stand-by mode. Only RUN TIME (TEMPS RESTANT) is illuminated,

the multi-display shows the remaining time until the program start. All other displays on the control panel are switched off in order to save energy. Pressing any arbitrary button cancels the stand-by mode.

24

Image 24

Contents ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do ifContents Safety Before Putting into Operation for the First TimeCorrect Use Child Safety General SafetyDisposal Environment TipsDispose the packing material For polyoxymethylene, e.g. plastic clipsUnit Description Front ViewDrawer for Washing Powder and Care Agent Control panel Program SelectorWool LAINE/ P Handwash Program Silk SOIE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua AlarmBefore the First Wash Prepare the Washing CycleSort and Prepare the Washing Washing Types and Care Codes How much washing detergent and care agent? Water SoftenerRun a Washing Cycle Brief InstructionsAfter the Washing Program Ends Setting the Washing Program Possible additional programs to suit the type of washingSet the program selector to Set the delay timer/soaking duration Delay timer Change the spin speed/Select rinse holdAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minuteSoaking duration Opening and closing the filling doorAdd the Washing If using Liquid Detergent/Tabs Add Washing Detergent and/Care AgentSection Washing Detergents and Care Agents Or for water softenerIf the delay timer is set Start the washing programCompletion of the Washing Program Program sequence displayMulti-display Display Residual MOISTURE%/LOADING%Washing cycle is finished/Remove the washing Abort programIt again Program is finishedToo much detergent was used in the just finished Program Tables WashingSeparate Conditioning/Starching/Impregnating Separate SpinCleaning and Care Washing Detergent DrawerWashing Drum Filling DoorCleaning the drain pump Before cleaning the drain pumpPump Gency EmptyingRemedying Faults What to do ifNot been removed Turn off the tap, then Open the water valve fully If the washing result is not satisfactory If the washing is grey and limescale forms in the drumIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation When all the washing solution has drained off Emergency Unlocking of the Filling DoorAdditional Rinse RINSE+ Set Additional RinseSolution Cooling Cancel Additional RinseTime Cycle before pumping off by incoming cold waterAdditional Rinse and Solution Cooling Set the Solution CoolingCancel the Solution Cooling Setting the Program Saving Function Canceling the Program Saving FunctionProgram Saving Child Safety Feature Setting the Child SafetyFeature Cancelling the Child Safety FeatureSetting UP and Connection Instructions Safety Instructions for InstallationSetting Up the Unit Remove the Transport SafeguardWhen transporting the unit with a sack trolley Transporting the UnitFirmly pull both hose holders off the unit Close off the hole with the plug cap GPrepare the Installation Location Setting Up on a Concrete PedestalSetting Up on a Vibrating floor Compensate for Floor Unevenness Electrical Connection Water ConnectionPermissible Water Pressure Water Inflow Water Drainage Water Drainage into a SiphonDraining the water into a basin Technical Data DimensionsDelivery Heads over 1m Measurements in mmPage Index Service When do you incur costs even during the warranty period?