AEG 88830 manual Electrical Connection, Water Connection, Permissible Water Pressure

Page 49

Setting up and connection instructions

Electrical Connection

Refer to the rating plate for details of the mains voltage, current type and the necessary fuses. The rating plate is located at the top behind the filling door.

; This unit conforms to the following EU directives:

the ”Low Voltage Directive" 73/23/EU with changes

the ”EMC Directive" 89/336/EWG with changes

Water Connection

3

The washing machine has safety features which prevent contamination

 

of the drinking water and which conform to the legal regulations of

the water authorities (e.g. for Germany: DVGW regulations). Other pro- tection measures in the installation are therefore not necessary.

Attention!

– Units for connection to cold water must not be connected to hot water!

– Use only new sets of hoses for connection!

Permissible Water Pressure

The water pressure must be at least 1bar (= 10N/cm2 = 0.1MPa), maxi- mum 10bar (= 100N/cm2 = 1MPa).

In the case of more than 10bar: Connect a pressure-reducing valve upstream.

In the case of less than 1bar: Unscrew the intake hose on the unit side on the inlet solenoid valve and remove the flow regulator (to do this, remove the filter with pointed pliers and remove the rubber washer behind). Replace the filter.

49

Image 49
Contents ÖKO-LAVAMAT 88830 update Dear customer Contents What to do if Solution CoolingContents Before Putting into Operation for the First Time SafetyCorrect Use General Safety Child SafetyEnvironment Tips DisposalDispose the packing material For polyoxymethylene, e.g. plastic clipsFront View Unit DescriptionDrawer for Washing Powder and Care Agent Program Selector Control panelSilk SOIE/ P Handwash Program Wool LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display Water Protection Aqua Control + Aqua Alarm What Does Update Mean?Prepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes Water Softener How much washing detergent and care agent?Brief Instructions Run a Washing CycleAfter the Washing Program Ends Possible additional programs to suit the type of washing Setting the Washing ProgramSet the program selector to Change the spin speed/Select rinse hold Set the delay timer/soaking duration Delay timerAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minuteOpening and closing the filling door Soaking durationAdd the Washing Add Washing Detergent and/Care Agent If using Liquid Detergent/TabsSection Washing Detergents and Care Agents Or for water softenerStart the washing program If the delay timer is setProgram sequence display Completion of the Washing ProgramMulti-display Display Residual MOISTURE%/LOADING%Abort program Washing cycle is finished/Remove the washingIt again Program is finishedToo much detergent was used in the just finished Washing Program TablesSeparate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpPump Gency EmptyingWhat to do if Remedying FaultsNot been removed Turn off the tap, then Open the water valve fully If the washing is grey and limescale forms in the drum If the washing result is not satisfactoryIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Emergency Unlocking of the Filling Door When all the washing solution has drained offAdditional Rinse RINSE+ Set Additional RinseCancel Additional Rinse Solution CoolingTime Cycle before pumping off by incoming cold waterSet the Solution Cooling Additional Rinse and Solution CoolingCancel the Solution Cooling Canceling the Program Saving Function Setting the Program Saving FunctionProgram Saving Setting the Child Safety Child Safety FeatureFeature Cancelling the Child Safety FeatureSafety Instructions for Installation Setting UP and Connection InstructionsRemove the Transport Safeguard Setting Up the UnitWhen transporting the unit with a sack trolley Transporting the UnitClose off the hole with the plug cap G Firmly pull both hose holders off the unitSetting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Measurements in mmPage Index When do you incur costs even during the warranty period? Service