AEG 88830 If the washing result is not satisfactory, If there are white residues on the washing

Page 37

Instructions for use

If the washing result is not satisfactory

If the washing is grey and limescale forms in the drum

•Not enough washing detergent added.

•The right washing detergent was not used.

•Special types of stain were not pretreated.

•Program or temperature incorrectly set.

•If binary wahing detergents were used, the individual components were not added in the correct ratio.

If there are still grey stains on the washing

•Washing contaminated with creams, grease or oils was washing with too little detergent.

•Washing at too low temperature.

•A frequent cause is that conditioner – particularly concentrated form, ended up on the washing. Wash out such stains as quickly as possible and carefully use the right conditioner.

If foam is still visible after the final rinse

•Modern washing detergents can still produce foam, even in the final rinse. The washing is still sufficiently rinsed.

If there are white residues on the washing

•These are the insoluble components of modern detergents. They are not the result of an insufficient rinsing effect.

Shake or brush off the washing. Perhaps in future you should turn the washing before washing it. Check the choice of detergent and use a liquid detergent if necessary.

37

Image 37

Contents ÖKO-LAVAMAT 88830 update Dear customer Contents What to do if Solution CoolingContents Before Putting into Operation for the First Time SafetyCorrect Use General Safety Child SafetyEnvironment Tips DisposalDispose the packing material For polyoxymethylene, e.g. plastic clipsFront View Unit DescriptionDrawer for Washing Powder and Care Agent Program Selector Control panelSilk SOIE/ P Handwash Program Wool LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display Water Protection Aqua Control + Aqua Alarm What Does Update Mean?Prepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes Water Softener How much washing detergent and care agent?Brief Instructions Run a Washing CycleAfter the Washing Program Ends Possible additional programs to suit the type of washing Setting the Washing ProgramSet the program selector to Change the spin speed/Select rinse hold Set the delay timer/soaking duration Delay timerAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minuteOpening and closing the filling door Soaking durationAdd the Washing Add Washing Detergent and/Care Agent If using Liquid Detergent/TabsSection Washing Detergents and Care Agents Or for water softenerStart the washing program If the delay timer is setProgram sequence display Completion of the Washing ProgramMulti-display Display Residual MOISTURE%/LOADING%Abort program Washing cycle is finished/Remove the washingIt again Program is finishedToo much detergent was used in the just finished Washing Program TablesSeparate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpPump Gency EmptyingWhat to do if Remedying FaultsNot been removed Turn off the tap, then Open the water valve fully If the washing is grey and limescale forms in the drum If the washing result is not satisfactoryIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Emergency Unlocking of the Filling Door When all the washing solution has drained offAdditional Rinse RINSE+ Set Additional RinseCancel Additional Rinse Solution CoolingTime Cycle before pumping off by incoming cold waterSet the Solution Cooling Additional Rinse and Solution CoolingCancel the Solution Cooling Canceling the Program Saving Function Setting the Program Saving FunctionProgram Saving Setting the Child Safety Child Safety FeatureFeature Cancelling the Child Safety FeatureSafety Instructions for Installation Setting UP and Connection InstructionsRemove the Transport Safeguard Setting Up the UnitWhen transporting the unit with a sack trolley Transporting the UnitClose off the hole with the plug cap G Firmly pull both hose holders off the unitSetting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Measurements in mmPage Index When do you incur costs even during the warranty period? Service