AEG 88830 manual Solution Cooling, Cancel Additional Rinse, Time

Page 40

Instructions for use

3.While RINSE+ (RINCAGE+) is flashing, release the button SOAKING (TREMPAGE).

After the flashing stops, the additional rinse is set. It is set until it is

canceled again.

When the additional rinse is set, the indicator RINSE+ (RINCAGE+) lights up on the program sequence disply before the program start and during the additional rinse.

4.If you want to check whether the additional rinse is set:

Turn the program selector to SHORT SPIN (ESSORAGE DELICAT).

Briefly press the button SOAKING (TREMPAGE).

The additional rinse is set if RINSE+ (RINCAGE+) flashes on the pro- gram sequence display.

Cancel Additional Rinse:

0 1. Turn the program selector to SHORT SPIN (ESSORAGE DELICAT).

2.Keep the button SOAKING (TREMPAGE) pressed for at least 5 seconds. As soon as the button is pressed, RINSE+ (RINCAGE+) flashes on the program sequence display. After 5 seconds, RINSE+ (RINCAGE+) stops flashing and lights up constantly for a further 5 seconds.

3.While RINSE+ (RINCAGE+) lights up constantly, release the button

SOAKING (TREMPAGE).

After RINSE+ (RINCAGE+) has stopped lighting up, the additional rinse is cancelled.

3

An additional rinse increases water consumption and the program run

 

time.

Solution Cooling

 

It may be necessary to cool down the washing solution before pumping

 

off in order to avoid thermal damage to plastic drainage pipes.

3

The washing solution is cooled down at the end of the main washing

 

cycle before pumping off (by incoming cold water).

(This setting is only effective for COTTONS/LINEN (BLANC/COULEURS) at temperatures of over 40 °C.)

No solution cooling is set when the unit is delivered.

40

Image 40
Contents ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do ifContents Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General SafetyDisposal Environment TipsDispose the packing material For polyoxymethylene, e.g. plastic clipsFront View Unit DescriptionDrawer for Washing Powder and Care Agent Control panel Program SelectorWool LAINE/ P Handwash Program Silk SOIE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua AlarmPrepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes How much washing detergent and care agent? Water SoftenerBrief Instructions Run a Washing CycleAfter the Washing Program Ends Possible additional programs to suit the type of washing Setting the Washing ProgramSet the program selector to Set the delay timer/soaking duration Delay timer Change the spin speed/Select rinse holdAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minuteOpening and closing the filling door Soaking durationAdd the Washing If using Liquid Detergent/Tabs Add Washing Detergent and/Care AgentSection Washing Detergents and Care Agents Or for water softenerIf the delay timer is set Start the washing programCompletion of the Washing Program Program sequence displayMulti-display Display Residual MOISTURE%/LOADING%Washing cycle is finished/Remove the washing Abort programIt again Program is finishedToo much detergent was used in the just finished Program Tables WashingSeparate Conditioning/Starching/Impregnating Separate SpinCleaning and Care Washing Detergent DrawerWashing Drum Filling DoorCleaning the drain pump Before cleaning the drain pumpPump Gency EmptyingRemedying Faults What to do ifNot been removed Turn off the tap, then Open the water valve fully If the washing result is not satisfactory If the washing is grey and limescale forms in the drumIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation When all the washing solution has drained off Emergency Unlocking of the Filling DoorAdditional Rinse RINSE+ Set Additional RinseSolution Cooling Cancel Additional RinseTime Cycle before pumping off by incoming cold waterSet the Solution Cooling Additional Rinse and Solution CoolingCancel the Solution Cooling Canceling the Program Saving Function Setting the Program Saving FunctionProgram Saving Child Safety Feature Setting the Child SafetyFeature Cancelling the Child Safety FeatureSetting UP and Connection Instructions Safety Instructions for InstallationSetting Up the Unit Remove the Transport SafeguardWhen transporting the unit with a sack trolley Transporting the UnitFirmly pull both hose holders off the unit Close off the hole with the plug cap GSetting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Technical Data DimensionsDelivery Heads over 1m Measurements in mmPage Index Service When do you incur costs even during the warranty period?