AEG 88830 manual Completion of the Washing Program, Program sequence display, Multi-display

Page 25

Instructions for use

Completion of the Washing Program

Program sequence display

Prior to the start the program steps to be executed are displayed by the program sequence display. The current program step is displayed during the washing program.


	Multi-display

	The expected remaining run time (in min-
	utes) until the completion of the program is
	shown in the multidisplay.
3	With the automatic program adaption by the control of the washing
	machine (quantity and type of washing, balance error recognition, spe-
	cial rinsing etc.) counting of the remaining run time can be stopped or
	corrected.
	Display RESIDUAL MOISTURE%/LOADING%
	(HUMIDITE%/CHARGE%)
	The following appears alternately at the display:


	• The expected residual moisture of the washing
	at the end of the program.
	This value depends on the set spin speed.
	• Load the washing drum (in steps of 10 percent.)
	This value is displayed only in COTTONS/LINEN (BLANC/COULEURS)
	programs and EASY-CARES/EASY IRON (MIXTES/FACILE A REPASSER).
	The washing machine can recognise the load only fifteen minutes
	after a program start.
	As soon as a value for the load is pending the display alternates
	between residual moisture and load.
	Overloading of the drum is displayed in values higher than
	100 percent (e. g.120).
3	Due to the differences in the fabrics and in the filling quantity the
	washing reaches for EASY CARE/EASY IRON (MIXTES/FACILE A

REPASSER) and DELICATES (DELICAT) a lower value for residual damp- ness than with COTTONS/LINENS (BLANC/COULEURS).

Change the Spin Speed

The spin speed can still be changed or the rinse hold (display 0) be set during the washing program.

Other settings cannot be changed.

25

Image 25

Contents ÖKO-LAVAMAT 88830 update Dear customer Contents What to do if Solution CoolingContents Before Putting into Operation for the First Time SafetyCorrect Use General Safety Child SafetyEnvironment Tips DisposalDispose the packing material For polyoxymethylene, e.g. plastic clipsFront View Unit DescriptionDrawer for Washing Powder and Care Agent Program Selector Control panelSilk SOIE/ P Handwash Program Wool LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display Water Protection Aqua Control + Aqua Alarm What Does Update Mean?Prepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes Water Softener How much washing detergent and care agent?Brief Instructions Run a Washing CycleAfter the Washing Program Ends Possible additional programs to suit the type of washing Setting the Washing ProgramSet the program selector to Change the spin speed/Select rinse hold Set the delay timer/soaking duration Delay timerAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minuteOpening and closing the filling door Soaking durationAdd the Washing Add Washing Detergent and/Care Agent If using Liquid Detergent/TabsSection Washing Detergents and Care Agents Or for water softenerStart the washing program If the delay timer is setProgram sequence display Completion of the Washing ProgramMulti-display Display Residual MOISTURE%/LOADING%Abort program Washing cycle is finished/Remove the washingIt again Program is finishedToo much detergent was used in the just finished Washing Program TablesSeparate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpPump Gency EmptyingWhat to do if Remedying FaultsNot been removed Turn off the tap, then Open the water valve fully If the washing is grey and limescale forms in the drum If the washing result is not satisfactoryIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Emergency Unlocking of the Filling Door When all the washing solution has drained offAdditional Rinse RINSE+ Set Additional RinseCancel Additional Rinse Solution CoolingTime Cycle before pumping off by incoming cold waterSet the Solution Cooling Additional Rinse and Solution CoolingCancel the Solution Cooling Canceling the Program Saving Function Setting the Program Saving FunctionProgram Saving Setting the Child Safety Child Safety FeatureFeature Cancelling the Child Safety FeatureSafety Instructions for Installation Setting UP and Connection InstructionsRemove the Transport Safeguard Setting Up the UnitWhen transporting the unit with a sack trolley Transporting the UnitClose off the hole with the plug cap G Firmly pull both hose holders off the unitSetting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Measurements in mmPage Index When do you incur costs even during the warranty period? Service