AEG 88830 manual Prepare the Installation Location, Setting Up on a Concrete Pedestal

Page 47

Setting up and connection instructions

Prepare the Installation Location

•The installation surface must be clean, dry and free of floor wax resi- due and other lubricating coatings so that the unit does not slide away. Do not use any lubricants as sliding aids.

•It is not recommended to set up the washing machine on deep-pile carpets or on floor coverings with soft foam underlays, as this would mean that the stability of the unit would not be guaranteed.

•Use ordinary rubber mats as underlays in locations with small-format tiles.

•Never use wood, card or similar underlays to compensate for minor floor unevenness. Always use the adjustable screw-type feet of the machine.

•If, for reasons of space, it is not possible to avoid setting up the unit next to a gas cooker or coal stove: Insert a thermally-insulating panel between the washing machine and the cooker (85 x 57cm). This panel must have an aluminium foil on the side against the cooker.

•The washing machine must not be set up in a room where there

is a danger of frost. Frost damage!

•The intake and drainage hoses must not be bent or pinched.

Setting Up on a Concrete Pedestal

When setting up the washing machine on a concrete pedestal, it is essential for safety reasons to fit stand plates in which the washing machine is then adjusted. The stand plates are available from the Customer Service under spare part number 645 425 058.

Setting Up on a Vibrating floor

In the case of vibrating floors, especially wooden beam floors with flex- ible boards, securely screw a water-resistant wooden panel at least 15mm thick onto at least 2 of the floor beams. If possible, set up the unit in a corner of the room where the wooden floor is best firmly installed and is therefore least likely to be susceptible to vibrations.

47

Image 47

Contents ÖKO-LAVAMAT 88830 update Dear customer Contents What to do if Solution CoolingContents Correct Use SafetyBefore Putting into Operation for the First Time General Safety Child SafetyFor polyoxymethylene, e.g. plastic clips DisposalEnvironment Tips Dispose the packing materialDrawer for Washing Powder and Care Agent Unit DescriptionFront View Program Selector Control panelSilk SOIE/ P Handwash Program Wool LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display Water Protection Aqua Control + Aqua Alarm What Does Update Mean?Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes Water Softener How much washing detergent and care agent?After the Washing Program Ends Run a Washing CycleBrief Instructions Set the program selector to Setting the Washing ProgramPossible additional programs to suit the type of washing COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Set the delay timer/soaking duration Delay timerChange the spin speed/Select rinse hold Adapted depending on the washing programAdd the Washing Soaking durationOpening and closing the filling door Or for water softener If using Liquid Detergent/TabsAdd Washing Detergent and/Care Agent Section Washing Detergents and Care AgentsStart the washing program If the delay timer is setDisplay Residual MOISTURE%/LOADING% Completion of the Washing ProgramProgram sequence display Multi-displayProgram is finished Washing cycle is finished/Remove the washingAbort program It againToo much detergent was used in the just finished Washing Program TablesSeparate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumGency Emptying Cleaning the drain pumpBefore cleaning the drain pump PumpWhat to do if Remedying FaultsNot been removed Turn off the tap, then Open the water valve fully If foam is still visible after the final rinse If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If there are still grey stains on the washingCarry Out an Emergency Emptying Operation Set Additional Rinse When all the washing solution has drained offEmergency Unlocking of the Filling Door Additional Rinse RINSE+Cycle before pumping off by incoming cold water Solution CoolingCancel Additional Rinse TimeCancel the Solution Cooling Additional Rinse and Solution CoolingSet the Solution Cooling Program Saving Setting the Program Saving FunctionCanceling the Program Saving Function Cancelling the Child Safety Feature Child Safety FeatureSetting the Child Safety FeatureSafety Instructions for Installation Setting UP and Connection InstructionsTransporting the Unit Setting Up the UnitRemove the Transport Safeguard When transporting the unit with a sack trolleyClose off the hole with the plug cap G Firmly pull both hose holders off the unitSetting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Measurements in mm Technical DataDimensions Delivery Heads over 1mPage Index When do you incur costs even during the warranty period? Service