AEG 88830 manual Setting Up the Unit, Transporting the Unit, Remove the Transport Safeguard, Tures

Page 45

Setting up and connection instructions

Setting Up the Unit

3	Washing machines with curved panels are not suitable for substruc-
	tures.

Transporting the Unit

•Do not place the washing machine on its front side or on its right side (looking from the front). Otherwise the electrical components can get wet.

•Never transport the unit without using the transport safeguard. Do not remove the transport safeguard until you reach the installation site. Transporting the unit without the transport safeguard can result in damage to the unit.

•Never lift the unit by the open filling door or by its base.

When transporting the unit with a sack trolley:

•Attach the sack trolley only at the side. The scoop of the sack trolley must not be longer than 24cm, otherwise the float switch can be destroyed.

Remove the Transport Safeguard

Attention! It is essential to remove the transport safeguard before putting the unit into oper- ation! Keep all parts of the trans- port safeguard in a safe place for possible later transport (moving house).

0 1. Open both hose holders on the rear of the unit and remove the hoses and the mains cable.

45

Image 45

Contents ÖKO-LAVAMAT 88830 update Dear customer Contents What to do if Solution CoolingContents Safety Before Putting into Operation for the First TimeCorrect Use General Safety Child SafetyEnvironment Tips DisposalDispose the packing material For polyoxymethylene, e.g. plastic clipsUnit Description Front ViewDrawer for Washing Powder and Care Agent Program Selector Control panelSilk SOIE/ P Handwash Program Wool LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display Water Protection Aqua Control + Aqua Alarm What Does Update Mean?Before the First Wash Prepare the Washing CycleSort and Prepare the Washing Washing Types and Care Codes Water Softener How much washing detergent and care agent?Run a Washing Cycle Brief InstructionsAfter the Washing Program Ends Setting the Washing Program Possible additional programs to suit the type of washingSet the program selector to Change the spin speed/Select rinse hold Set the delay timer/soaking duration Delay timerAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minuteSoaking duration Opening and closing the filling doorAdd the Washing Add Washing Detergent and/Care Agent If using Liquid Detergent/TabsSection Washing Detergents and Care Agents Or for water softenerStart the washing program If the delay timer is setProgram sequence display Completion of the Washing ProgramMulti-display Display Residual MOISTURE%/LOADING%Abort program Washing cycle is finished/Remove the washingIt again Program is finishedToo much detergent was used in the just finished Washing Program TablesSeparate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpPump Gency EmptyingWhat to do if Remedying FaultsNot been removed Turn off the tap, then Open the water valve fully If the washing is grey and limescale forms in the drum If the washing result is not satisfactoryIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Emergency Unlocking of the Filling Door When all the washing solution has drained offAdditional Rinse RINSE+ Set Additional RinseCancel Additional Rinse Solution CoolingTime Cycle before pumping off by incoming cold waterAdditional Rinse and Solution Cooling Set the Solution CoolingCancel the Solution Cooling Setting the Program Saving Function Canceling the Program Saving FunctionProgram Saving Setting the Child Safety Child Safety FeatureFeature Cancelling the Child Safety FeatureSafety Instructions for Installation Setting UP and Connection InstructionsRemove the Transport Safeguard Setting Up the UnitWhen transporting the unit with a sack trolley Transporting the UnitClose off the hole with the plug cap G Firmly pull both hose holders off the unitPrepare the Installation Location Setting Up on a Concrete PedestalSetting Up on a Vibrating floor Compensate for Floor Unevenness Electrical Connection Water ConnectionPermissible Water Pressure Water Inflow Water Drainage Water Drainage into a SiphonDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Measurements in mmPage Index When do you incur costs even during the warranty period? Service