Sharp HT-CN300W Installing the speakers on the wall, Wall, Changing the speaker angle

Page 16

HT-CN300W

Installing the speakers on the wall

wall -

Front, centre and surround speakers can be mounted on the wall and their angle can be adjusted. Each speaker needs 3 screws to be mounted (not supplied).

The design of the speakers allows them to be hung on the wall.

Be sure to use the type and size of the screw that are shown below.

3.2 mm (1/8")

5 mm (3/16")

9 mm (3/8")

Min. 22 mm (7/8")

1 Drive one screw into the wall for each speaker, as shown in the illustration.

3 Raise the speaker the most upward. (Refer to "Changing the speaker angle" for details.)

4 Drive two screws into the wall.

Label Label

Use the round labels for hiding mounting screws.

5 Perform steps 1 - 4 to mount other speakers.

Speaker Installation - Installing the speakers on the

	3.5 mm (9/64")
	Wall mounting screw
	(not supplied)
Wall surface	Min. 18.5 mm (23/32")
Wall surface

zMake sure that both the screw and the wall can support a load of 20 kg (45 lbs.).

zDrive the screw, so the screw head extends about 3.5 mm (9/64") out from the wall.

2 Install the speaker on the wall by inserting the screw head into the slot on the back of the speaker.

Recess

Wall surface

Set the speaker lead in the recess, preventing it from being caught between the wall and the speaker.

Changing the speaker angle:

Whilst holding down the angle adjusting lever, move the speaker to the marking and then release the lever.

The speaker angle can be adjusted in 5 levels.

Mark

Caution:

Check the stability of the ceiling or wall fully. Sharp is not liable for accidents caused by insufficient stability of the ceiling or wall, or improper mounting.

The speaker may fall due to unstable mounting.

If you need any assistance, contact the dealer you purchased the system from. The following may cause personal injury or speaker damage.

Applying any other load to the fittings than the speaker.

Modification or change of the fittings.

Stepping on or hanging from the speakers. Especially pay attention to small children.

15

02/7/11 HT-CN300W_A_3.fm

Image 16

Contents HT-CN300W Contents Special notesAccessories AccessoriesPrecautions „ Volume control„ General Do not remove the outer cover, as this may resultIndicators Controls and indicatorsControls „ Main unit with subwoofer ReferenceFull-Range Speaker Angle Adjusting Lever Label indication „ Remote control sensor„ Front/Centre/Surround speakers Speaker connections Speaker connectionsAerial connection AerialConnecting other equipment Connecting other equipment„ Connecting the TV „ Connecting the DVD player„ Selecting the colour TV system „ Connecting the camcorder, satellite receiver, etc. VideoTo select the colour TV system Connecting to the AC socket „ Setting the AC voltage selector„ Plugging in the remote control Before connecting„ To turn the power on „ Setting the FM/AM span selectorConnections Connecting to the AC socket Speaker system Placing the speaker systemPlacing Installing the speakers on the wall WallPerform steps 1 4 to mount other speakers Changing the speaker anglePreparing the remote control „ Battery installation „ Test of the remote control„ How to open the remote control cover Precautions for battery useHT-CN300WOperation buttons on the remote control Remote control„ Operation buttons for the main unit Operation buttons on„ Switching the operation buttons for the main unit „ Operation buttons for other equipmentInitial setting for Memory 1 buttons „ Memory 1/2 buttons for other equipmentMemory 1 buttons Memory 2 buttonsMemorising the remote control buttons Remote Control Memorising the remote control buttonsUsing the supplied labels „ Initialising the remote control buttonsMove the LEARN/TRANSMIT selector switch to Transmit Setting the clock Basic Operation Setting the clockTo readjust the clock To confirm the time displayDisplay control Sound controlSound sound mode Enjoy Surround Sound sound modeEnjoy Surround Acoustic effect Standard Dynamic soundVirtual Stereo„ Sound mode „ To enjoy with dynamic soundAuto tuning HT-CN300WListening to the radioBasic Operation Listening to the radio To receive an FM stereo transmission„ To scan the preset stations „ To erase all the contents of the preset MemoryListening to a memorised station „ Memorising a stationSpeaker settings „ Speaker size settingSpeaker settings Speaker type Speaker size„ Speaker delay setting Speaker type Adjustable range„ Test tone „ Speaker level settingFL CT FR SW SL SR Timer and sleep operation „ Setting the timerAdvanced Features Timer and sleep operation Adjust the volume using the Volume or button„ Setting the sleep timer Troubleshooting chart Troubleshooting chart„ Operation „ SoundError indicators and warnings Maintenance„ Cleaning the cabinet „ TV imageSpecifications Specifications„ Amplifier „ SubwooferMemo Memo Sharp Corporation