Sharp HT-CN300W operation manual Aerial connection

Page 9

The speaker terminals on the main unit, the tube and plugs of the speaker lead, and speaker labels are distinguished by colour.

Connect the speaker and the unit by matching the colours. Connect the speaker wires to the speakers first, then to the unit.

Speaker

Label

Recess

Black

Red

Tube

Main unit

Label

 

Plug in with the rising

Speaker plug

side facing up.

 

Caution:

zOnly the supplied speakers should be used with this unit.

zMake sure to connect the speakers after unplugging the unit.

zDo not mistake and , and right and left terminals of the speaker leads.

zDo not let the bare speaker wires touch each other.

zDo not stand or sit on the speakers. You may be injured.

zInsert the speaker plug fully with the rising side facing up.

zHold the speaker plug when removing it from the unit. Pulling the lead may cause breakage.

Aerial connection

HT-CN300W

 

Connect the FM/AM loop aerial to the ANTENNA socket.

Position the FM aerial wire and rotate the AM loop aerial for optimum reception.

 

Place the AM loop aerial on a shelf, or attach it to a stand or on a wall with screws

 

(not supplied).

 

-

Notes:

 

connections

 

 

z Placing the aerial on the unit, or near the AC power lead or the remote sensor may

 

cause noise pickup. Place the aerial away from the unit for better reception.

 

z Do not connect the attached FM aerial to an external FM aerial. Otherwise, trouble

 

may occur.

 

 

Installing the AM loop aerial:

 

 

< Assembling >

< Attaching to the wall >

Connections sensorcontrolRemote/

Wall

Screws

 

(not supplied)

 

 

 

Remote control sensor connection

 

Connect the plug of the remote

 

 

control sensor and push the plug

 

 

cover until it clicks.

 

Aerial/

Plug

Plug cover

Speaker-

Removing the remote control sensor:

 

Push the upper and lower sides of the plug cover and take the Push

 

plug off the unit to disconnect the remote control sensor.

 

 

Push

 

Caution:

zHold the connection plug of the remote control sensor when removing it from the unit. Pulling the lead may cause breakage.

zMake sure of the top and bottom of the plug when plugging in the remote control sensor.

8

02/7/11 HT-CN300W_A_2.fm

Page 8 Page 10
Image 9
Page 8 Page 10
Contents HT-CN300W Special notes ContentsAccessories Accessories„ Volume control Precautions„ General Do not remove the outer cover, as this may resultControls and indicators IndicatorsControls Reference „ Main unit with subwoofer„ Remote control sensor Full-Range Speaker Angle Adjusting Lever Label indication„ Front/Centre/Surround speakers Speaker connections Speaker connectionsAerial Aerial connectionConnecting other equipment Connecting other equipment„ Connecting the DVD player „ Connecting the TV„ Connecting the camcorder, satellite receiver, etc. Video „ Selecting the colour TV systemTo select the colour TV system „ Setting the AC voltage selector Connecting to the AC socket„ Plugging in the remote control Before connecting„ Setting the FM/AM span selector „ To turn the power onConnections Connecting to the AC socket Placing the speaker system Speaker systemPlacing Wall Installing the speakers on the wallPerform steps 1 4 to mount other speakers Changing the speaker angle„ Battery installation „ Test of the remote control Preparing the remote control„ How to open the remote control cover Precautions for battery useRemote control HT-CN300WOperation buttons on the remote control„ Operation buttons for the main unit Operation buttons on„ Operation buttons for other equipment „ Switching the operation buttons for the main unit„ Memory 1/2 buttons for other equipment Initial setting for Memory 1 buttonsMemory 1 buttons Memory 2 buttonsRemote Control Memorising the remote control buttons Memorising the remote control buttons„ Initialising the remote control buttons Using the supplied labelsMove the LEARN/TRANSMIT selector switch to Transmit Basic Operation Setting the clock Setting the clockTo readjust the clock To confirm the time displaySound control Display controlEnjoy Surround Sound sound mode Sound sound modeEnjoy Surround Dynamic sound Acoustic effect StandardVirtual Stereo„ To enjoy with dynamic sound „ Sound modeHT-CN300WListening to the radio Auto tuningBasic Operation Listening to the radio To receive an FM stereo transmission„ To erase all the contents of the preset Memory „ To scan the preset stationsListening to a memorised station „ Memorising a station„ Speaker size setting Speaker settingsSpeaker settings Speaker type Speaker sizeSpeaker type Adjustable range „ Speaker delay setting„ Speaker level setting „ Test toneFL CT FR SW SL SR „ Setting the timer Timer and sleep operationAdvanced Features Timer and sleep operation Adjust the volume using the Volume or button„ Setting the sleep timer Troubleshooting chart Troubleshooting chart„ Operation „ SoundMaintenance Error indicators and warnings„ Cleaning the cabinet „ TV imageSpecifications Specifications„ Amplifier „ SubwooferMemo Memo Sharp Corporation
Top Page Image Contents