Sharp HT-CN300W operation manual Memorising the remote control buttons

Page 21

Memorising the remote control buttons

HT-CN300W

You can assign only one function to each button. If you assign two functions to the button, the newer one will be memorised (learn function).

„Memorising operations in the Memory 2

buttons for other equipment

The same buttons are used for both Memory 1 and 2 operations. To store signals in Memory 1 buttons, set the MEMORY 1/2 selector switch to MEMORY 1, and for Memory 2 buttons, set the switch to MEMORY 2.

1 Set the MEMORY 1/2 selector switch to MEMORY 2.

2 Move the LEARN/TRANSMIT selector switch to LEARN.

The red learn indicator will light up. Though the red and green learn indicators light up alternately after approx. 15 seconds, you can go on to the next step.

Lights up	Alternately light up

3 Press down the desired button on the remote control for 2 seconds or more.

The green learn indicator will flash (the red indicator remains lit).

Lit Flashes

4 Within 10 seconds, press down for more than 2 seconds the

desired button on the remote control supplied with other equipment to send the signal to the marking.

Angle and distance

5 cm - 10 cm (2" - 4")

10˚

When the signal is sent to the remote control of the unit, the green indicator will go off. When memorisation is completed, it will light up.

Lit Goes off

Lit Lights up

mark

If the signal is not memorised correctly, the

red learn indicator will flash. Perform theFlashes operations from step 3 again.

5 Repeat steps 3 and 4 to memorise other buttons.

6 After memorisation is completed, move the LEARN/TRANSMIT selector switch to TRANSMIT.

You can use the remote control.

Notes:

zYou cannot store all the button operations by pressing only one button on the remote control of other equipment. Memorise them one by one.

zAfter storing operation is completed, check that other equipment works correctly with the remote control.

zSome functions cannot be memorised depending on other equipment.

Remote Control - Memorising the remote control buttons -

20

02/7/11 HT-CN300W_A_3.fm

Image 21

Contents HT-CN300W Special notes ContentsAccessories Accessories„ Volume control Precautions„ General Do not remove the outer cover, as this may resultControls and indicators IndicatorsControls Reference „ Main unit with subwoofer„ Remote control sensor Full-Range Speaker Angle Adjusting Lever Label indication„ Front/Centre/Surround speakers Speaker connections Speaker connectionsAerial Aerial connectionConnecting other equipment Connecting other equipment„ Connecting the DVD player „ Connecting the TV„ Connecting the camcorder, satellite receiver, etc. Video „ Selecting the colour TV systemTo select the colour TV system „ Setting the AC voltage selector Connecting to the AC socket„ Plugging in the remote control Before connecting„ Setting the FM/AM span selector „ To turn the power onConnections Connecting to the AC socket Placing the speaker system Speaker systemPlacing Wall Installing the speakers on the wallPerform steps 1 4 to mount other speakers Changing the speaker angle„ Battery installation „ Test of the remote control Preparing the remote control„ How to open the remote control cover Precautions for battery useRemote control HT-CN300WOperation buttons on the remote control„ Operation buttons for the main unit Operation buttons on„ Operation buttons for other equipment „ Switching the operation buttons for the main unit„ Memory 1/2 buttons for other equipment Initial setting for Memory 1 buttonsMemory 1 buttons Memory 2 buttonsRemote Control Memorising the remote control buttons Memorising the remote control buttons„ Initialising the remote control buttons Using the supplied labelsMove the LEARN/TRANSMIT selector switch to Transmit Basic Operation Setting the clock Setting the clockTo readjust the clock To confirm the time displaySound control Display controlEnjoy Surround Sound sound mode Sound sound modeEnjoy Surround Dynamic sound Acoustic effect StandardVirtual Stereo„ To enjoy with dynamic sound „ Sound modeHT-CN300WListening to the radio Auto tuningBasic Operation Listening to the radio To receive an FM stereo transmission„ To erase all the contents of the preset Memory „ To scan the preset stationsListening to a memorised station „ Memorising a station„ Speaker size setting Speaker settingsSpeaker settings Speaker type Speaker sizeSpeaker type Adjustable range „ Speaker delay setting„ Speaker level setting „ Test toneFL CT FR SW SL SR „ Setting the timer Timer and sleep operationAdvanced Features Timer and sleep operation Adjust the volume using the Volume or button„ Setting the sleep timer Troubleshooting chart Troubleshooting chart„ Operation „ SoundMaintenance Error indicators and warnings„ Cleaning the cabinet „ TV imageSpecifications Specifications„ Amplifier „ SubwooferMemo Memo Sharp Corporation