Sharp HT-CN300W operation manual „ Setting the sleep timer

Page 34

HT-CN300W

Timer and sleep operation (continued)

Features -

When the preset time is reached:

zPlayback starts automatically and the volume increases gradually.

zThe unit will enter the power stand-by mode one hour after the timer playback starts.

To reset or change the timer setting:

Perform "Setting the timer" from the beginning (page 32).

Cancelling the timer playback:

Timer is cancelled by turning the power on whilst in the timer stand-by mode.

Notes:

zOnce the time is set, the setting will be retained until a new time is entered.

zThe contents of the setting will be erased if the unit is unplugged or a power failure occurs. In such cases, set the timer again.

zYou can select the other source in step 2 of "Setting the timer", but this unit cannot set the timer of other equipment.

zWhen in the timer stand-by mode, the X-BASS button does not allow you to enter the demonstration mode.

4 Press the ENTER button.

The sleep timer indicator lights up.

5 Your system will enter the power stand-by mode automatically after the preset time has elapsed.

The volume will be turned down 1 minute before the sleep operation finishes.

At that time, you cannot change the volume.

Note:

You can select the other source in step 1 of "Setting the sleep timer", but this unit cannot set the sleep timer of other equipment.

Advanced - Timer and sleep operation

„Setting the sleep timer

You can set the unit to the power stand-by mode at the specified time.

1 Press the TUNER/BAND button.

Tune in to the desired station. (See page 27.)

2 Press the TIMER/SLEEP button repeatedly until "SLEEP" is displayed.

3 Press the or button to change the sleep time.

(Maximum: 3 hours/Minimum: 1 minute)

To confirm the remaining sleep time:

Press the TIMER/SLEEP button.

zThe remaining sleep time is displayed for about 5 seconds.

zYou can change the remaining sleep time whilst it is displayed by pressing the ENTER button (steps 3 - 4).

To cancel the sleep operation:

Press the ON/ (STAND-BY) button whilst the sleep timer is set.

To cancel the sleep timer without setting the unit to the stand-by mode, proceed as follows.

1Press the TIMER/SLEEP button.

2Within 5 seconds, press the ENTER button.

3Press the or button to select "SLEEP0:00", and press the ENTER button.

z3 hours - 5 minutes 5-minute intervals

z5 minutes - 1 minute 1-minute intervals

33

02/7/11 HT-CN300W_A_4.fm

Image 34

Contents HT-CN300W Contents Special notesAccessories Accessories„ General Precautions„ Volume control Do not remove the outer cover, as this may resultIndicators Controls and indicatorsControls „ Main unit with subwoofer ReferenceFull-Range Speaker Angle Adjusting Lever Label indication „ Remote control sensor„ Front/Centre/Surround speakers Speaker connections Speaker connectionsAerial connection AerialConnecting other equipment Connecting other equipment„ Connecting the TV „ Connecting the DVD player„ Selecting the colour TV system „ Connecting the camcorder, satellite receiver, etc. VideoTo select the colour TV system „ Plugging in the remote control Connecting to the AC socket„ Setting the AC voltage selector Before connecting„ To turn the power on „ Setting the FM/AM span selectorConnections Connecting to the AC socket Speaker system Placing the speaker systemPlacing Perform steps 1 4 to mount other speakers Installing the speakers on the wallWall Changing the speaker angle„ How to open the remote control cover Preparing the remote control„ Battery installation „ Test of the remote control Precautions for battery use„ Operation buttons for the main unit HT-CN300WOperation buttons on the remote controlRemote control Operation buttons on„ Switching the operation buttons for the main unit „ Operation buttons for other equipmentMemory 1 buttons Initial setting for Memory 1 buttons„ Memory 1/2 buttons for other equipment Memory 2 buttonsMemorising the remote control buttons Remote Control Memorising the remote control buttonsUsing the supplied labels „ Initialising the remote control buttonsMove the LEARN/TRANSMIT selector switch to Transmit To readjust the clock Setting the clockBasic Operation Setting the clock To confirm the time displayDisplay control Sound controlSound sound mode Enjoy Surround Sound sound modeEnjoy Surround Virtual Acoustic effect StandardDynamic sound Stereo„ Sound mode „ To enjoy with dynamic soundBasic Operation Listening to the radio Auto tuningHT-CN300WListening to the radio To receive an FM stereo transmissionListening to a memorised station „ To scan the preset stations„ To erase all the contents of the preset Memory „ Memorising a stationSpeaker settings Speaker settings„ Speaker size setting Speaker type Speaker size„ Speaker delay setting Speaker type Adjustable range„ Test tone „ Speaker level settingFL CT FR SW SL SR Advanced Features Timer and sleep operation Timer and sleep operation„ Setting the timer Adjust the volume using the Volume or button„ Setting the sleep timer „ Operation Troubleshooting chartTroubleshooting chart „ Sound„ Cleaning the cabinet Error indicators and warningsMaintenance „ TV image„ Amplifier SpecificationsSpecifications „ SubwooferMemo Memo Sharp Corporation