Alliance Laundry Systems HF234, HF304, HF185, HF150 Maintenance instruction of the machine

Page 40

Maintenance instruction of the machine

7

WARNING

To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not disconnect this appliance from the power supply.

Before starting wiring or inspection, power must be switched OFF, check to make sure that the operation panel indicator is off.

Any person who is involved in wiring or inspection shall wait for at least 10 minutes after the power supply has been switched OFF and check that there is no residual voltage using a tester or the like. The capacitor of the inverter or the EMC filter is charged with a high voltage for some time after power OFF, and it is dangerous.

End of day

General maintenance

Periodical maintenance

Clean AC drive filter:

a.Snap off external plastic cover which contains filter.

b.Remove foam filter from cover.

c.Wash filter with warm water and allow to air dry. Filter can be vacuumed clean.

Clean the entire cabinet of the machine regularly and remove all traces of soap, etc....

Remove all detergent residue in the soap dispenser with hot water.

Clean the door gasket and remove all detergents and other products.

Shut off the main water, steam, and power connections at the end of each day. Do not change the setting of the water inlet taps on boiler fed machines once these have been installed.

It is recommended to leave the door and soap dispenser open after use, to ventilate the machine.

Check for proper door lock operation on a daily basis.

The V-belts of the motors should be retightened after two to three months when first used. This is necessary because these belts are subject to a one-time stretching when first used. If this is not done, the belt starts to slip after a few months and will break shortly afterwards.

Check the water inlet filters to make sure they are not blocked by calcification.

Check the drain valve for obstructions.

If a machine frequently skips the final spin, check whether the probe of the out of balance switch is still in the appropriate position, that is horizontally centered and vertically 1/3 from the bottom inside the window. (When the drum is empty).

Lubricate the bearings after every 200 hours of operation or replace the automatic lubricator annually.

40

Image 40
Contents Washer Extractors Page Contents Internal connections of the electrical heating  Model Numbers Build-upSafety and Environmental Informations SafetyEnvironmental Disposal of UnitExplanation of Safety Messages Important Safety Instructions Page Operator Safety Technical data and dimensions Technical data HF150, IHF150, IHF033, CHF150, CHF033Dimensions HF150, IHF150, IHF033, CHF150, CHF033 Technical data HF185, IHF185, IHF045, CHF185, CHF045 Dimensions HF185, IHF185, IHF045, CHF185, CHF045 Technical data HF234, IHF234, IHF055, CHF234, CHF055 Dimensions HF234, IHF234, IHF055, CHF234, CHF055 Technical data HF304, IHF304, IHF075, CHF304, CHF075 Dimensions HF304, IHF304, IHF075, CHF304, CHF075 Out of balance switch Installation and Connection InstructionsSurface Removal of the transport safety HF234-304665 733 680 780 765 833 680 780 830 900 738 960 1040 97.5 865 1060 Water connection Water drainElectrical installation Important Do not use fuses in place of a circuit breakerGrounding Instructions Machine Power Cable Connections Main power connectionConnection label Page Boiler Fed/Steam Heat Electric Heat Alternative Electric Heat OptionsLiters / 45 pounds Liters / 55 pounds Liters / 75 pounds Liquid soap connection option Connection of the liquid soap hosesWith an external tension 24V DC See Label Label Steam connection With direct steam injection into the machine See TableTechnical remarks Internal connections of the electrical heatingMaintenance instruction of the machine End of day General maintenance Periodical maintenanceAnnual maintenance HF150HF185 HF234Nameplate Contact InformationNameplate Location Replacement Parts Repair and after-sales service